How to make a moonshine machine from a pressure cooker

How to make a moonshine apparatus from the pressure cooker do it yourself

Hello everyone! For a long time I promised to write this article, but he was constantly postponed. It's time to fulfill the promise. Today I will tell how to make a moonshine apparatus from the pressure cooker with your own hands.

Content

What is the moonshine apparatus

Let's first remind you to start, from which it consists and how the homemade moonshine apparatus works. The simplest construction includes a distillation cube (boiling capacity) and a refrigerator (direct or serpentine). The diagram is shown in the figure below.

Braga is poured into hermetic container and heats up to evaporation of alcohol from it. The pair are then falling into the refrigerator, where they are condensed into the moonshine. Sometimes the design includes additional equipment, such as an amrernant. Read more in the article to prepare a moonshine.

We make a distillation cubic

I will make a distillation cube from the old Soviet aluminum pressure cooker for 6 liters. It is an almost perfect option for this.

I speak almost, because She has a significant drawback - its volume. You can pour into such a container not more than 5 liters of Braga, from which approximately 1 liter of 45% of the moonshine.

I do not lie to tell you, but it's enough to start driving a moonshine and understand whether you want to do this business. And the occupation is very exciting, believe me.

So, we have such a pressure cooker.

I got it from my parents, but also to buy it will not be difficult. I just found at Avito exactly the same as 400 rubles.

First of all, it is necessary to cut into the nipple cover to connect a distillation cube with a refrigerator. I will insert this, with a thread on ½ ".

In the lid there are already two holes for valves for pressure relief, we will not touch them. Let them perform their function. We will make a new hole with a drill on a tree with a size of 20.

Why on wood? Yes, it is just much cheaper than the metal drill, and the aluminum cuts very well.

First you need to mark the center and drill a small drill hole for centering.

And then drill it with a large drill.

If there are inaccurate edges, they must be cleaned with a small notch with a shallow notch. Now you can insert nipple.

After the drill size 20, the hole is well suited for nipple ½ ", I even had to apply the key to be screwed. He sat down so tightly that no additional gaskets or seals do not need.

From the inside, tighten the nipple nut.

It screws up the fitting for fastening the hose Ø12 mm.

If your pressure cooker has a gasket, the distillation cube for a homemade moonshine is ready. I did not have it. Therefore, we will make it.

We make a gasket for sealing cube

What a rubber got here is not suitable here, with contact with the moonshine couples, it will smell and spoil our entire product. It needs silicone here, and not simple, but food.

You can buy a ready-made gasket or if you do not find a suitable size, buy a sheet and cut the gasket yourself. They are sold in stores for moonshivers and in stores with laboratory equipment.

I will make a laying of liquid silicone for aquariums. It can be bought in pet stores, construction supermarkets and plumbing stores.

It is necessary for aquariums, it is precisely safe and does not give extraneous smells.

Fill with a small slide groove for laying on the lid and let Silicon dry. After a day, you can already start distillation.

Go to the next step.

We make a refrigerator

Now we need a refrigerator. You can buy it, for example here there is a good and inexpensive coil. And you can make it yourself. For this, I have a separate article - the manufacture of the direct-flow refrigerator.

Than to connect details

Now it remains only to connect the distillation cube and refrigerator. For this, I use a silicone hose with an inner diameter of 12 mm. The hose should also be made of food silicone. No rubber or PVC!

Now the moonshine apparatus is ready. In order to prepare your first drink this is enough.

Tips and comments

  1. You can add a self-made drill to this design.
  2. If the fitting in the lid is set with a gap, then it can be sealed with the same silicone.
  3. It would be possible to do without nipple, and into the cover to embed a fitting with an external thread at once. But with Nipples, we get a more versatile design.
  4. Moonshine must be driven correctly, for this I advise you to read the article - double fractional distillation.
  5. After the manufacture of the moonshine, I advise you to test it on distillation of water.
  6. For emergency seals, the leaks in the device fits well enough dough. I managed at all without a sealing gasket.

That's all. The process is very simple and not long. If you have ideas or comments, then leave them in the comments. I am always happy with constructive criticism. Also subscribe to the news, I will soon plan to add braga recipes.

So far. Dorofeev Paul.

Read, it is also interesting:

I want to say about the fitting and other San technical fittings. When I went shopping Plumbing, then I will face a problem - it is not always there is a silver fittings, similar to a stainless steel. Brass as much as you like. So, there are "silver" and what kind of metal, the experienced seller immediately asked "for the device something? ". And then explained that it was just a spraying or a galphine that heats almost immediately from the vapor during distillation. And under it the same brass.

Of course, we would like all these parts of the stainless steel, but as I understood them to be ordered from Tokarey, or somewhere else. So you have to put up with brass, hoping that the accessories for drinking water is brass, and as I understand not harmful.

I reread not one of your article. Everywhere a banal error: water supply is not correct. Correct the water to meet the cooled product, i.e. Closer to the product output, the water inlet is connected to the refrigerator, and the tap (draining water) is connected closer to the inlet to the refrigerator.

Thank you for your comment. All right, cooling water should go to the meeting a pair. I wrote about this in the article about the manufacture of the cooler. I have an error in the picture, which is duplicated in several articles. I constantly forget to fix it. I will try to take up the other day.

The design for beginners is good, but who has a brain and hands, he can find his original solution. I started alcohol in my youth by the secret of my parents from Mogon. Braga put in a bottle of 0.7l from the port. The device was like this: a cube custard-enameled kettle; The refrigerator is a rubber hose from the shower, a piggy in a spiral and placed in a tin can from under the Bulgarian green peas. How changed the heated water has already forgotten. After the rubber hose replaced the copper spiral, but this spoiled the entire product. The bitter greens and moonshine had to pour into the sink.

In the army thought over the new project of the device and made sketches. It is a pity that they are not survived. There was a project of a straight-error from the rubber hose from the washing machine and a balcony box for growing colors. What I wanted to make a cube no longer remember. It seems from the pan.

Later, dad showed how to drive a moonshine without apparatus. Miscome method in a saucepan, and on top of all the closed design is covered by a bowl with coolant. On it, the alcohol condenses and flows into the inside bowl. The entire distillation process occurs in a closed container. The system is of course wretched, but may come for beginners.

Pavel. Here is such a question, I have a device with a dry character, and such a feeling that the refrigerator is not enough, the refrigerator itself is like ice, but you start to add a minimum to the middle of the induction slab as it starts to snort. What do you think by making the hose at the exit length about the meter it will solve the problem that it does not have time to condense in the refrigerator condensed in the hose. At the moment I have a hose at the output of about 15 cm

Hose Vryatly will help. Do you have a right supply of water carried out? Cold water should go to the meeting a couple.

It is also possible that you have a serpentor incorrectly made and there are places with a negative slope in which the liquid accumulates.

What power of heating is your device? If there is no accompanying documentation, then you can ask the seller. And if you bring down a smaller power, and it starts to snatch and spit, then you must make a claim to the manufacturer.

Paul answered you right. Improper water supply how to drink. Being cannot be that the factory apparatus spoil the ferry at the exit. The refrigerator must be filled with water completely. Be sure to apply water from below, and take it from above. Otherwise, no exit hoses will help. To condensate the pair, you need a large surface and a significant temperature difference.

Moonshine apparatus from the pressure cooker do it yourself

Homemade moonshine-based moonshops found recently tremendous popularity among consumers. The advantages of such an aggregate are undoubted. First, the pressure cooker can be bought in any store technique, secondly, it is an absolutely sealed container, equipped with two holes under the input and output valve. Thirdly, the built-in thermometer allows you to control the boiling point.

In order for the moonshine apparatus from the pressure cooker with their own hands it will only be necessary to increase the holes on the lid, add a refrigerator, an amar furnace and the simplest communications in the form of silicone hoses. How to do it right - in our article. Here you will find video from experienced dumbers and assembly recommendations.

The pressure cooker is a household appliance or pan with a hermetically closed lid. Due to such sealing during operation, increased pressure is formed, which allows you to prepare food at a higher temperature. This is how it is impossible to be suitable for the distillation of Braga. The pressure inside the pressure cooker reaches 200 kPa, which, on the one hand, allows Brage to boil faster, on the other - increase the speed of evaporation of alcohol-containing vapors.

What kind of pressure cooker will get a great moonshine apparatus

Choosing a pressure cooker, you need to pay attention to the wall thickness and the material from which they are made. Optimal is a pressure cooker from high-quality food stainless steel with a flat surface. This makes it possible to put an aggregate on any plane. Be sure to have 3-4 layers of the bottom, which will exclude the burning and loss of heat. Choose those devices that are used on a specific type of burner - gas, electrical or induction.

In addition, if you are just starting to learn moonshine, purchase a better electric pressure cooker equipped with a thermal sensor. This will allow you to establish a certain temperature and maintain it throughout the time of the distillation of Braga.

The disadvantage of such an apparatus is only one - small volume. The largest household pressure cooker consists of a 6-liter bowl. From this number of Braga, only 1-1.5 liters of the "dirty" moonshine will be obtained, and if you remove the tails and head and overtakes again, it turns out 0.75 liters. A little, of course, but quite enough for home use. Moreover, the cooking process itself is so simplified by the presence of a pressure cooker, which can be repeated on the same day.

In the pressure cooker, the braga is poured only on 2/3 volumes.

We collect a moonshine apparatus from the pressure cooker

In the pressure cooler cover, we saw the holes, in one of which the fitting or the feut is inserted, and in the second - bimetallic thermometer.

Sanitary futo provides the most sealed connection, so it will be better to stop on such threaded connections. For the lid you need 2 hours of 1/2 inches thread.

A silicone hose for a connection with a coil is put on a feuttone, and in the second insert a bimetallic thermometer, if there is no built-in pressure cooker.

All connections must be absolutely hermetic so that the alcohol-containing pairs do not pass. Some prefer to make silicone plugs, others use the usual dough.

Connecting tubes that are connected by a distillation cube and a serpentine can be made of silicone - relatively inert material, withstanding high temperatures, as well as from glass - perfect option. You can stop the choice and on the copper tube, it also does not react with alcohol. It is strictly forbidden to use plastic and rubber hoses - the caustic smell and bitterness will be reduced to not all the cooking efforts.

This is how the scheme of the assembly of the moonshine apparatus from the pressure cooker is:

Condenser (Graham Refrigerator)

With regard to the moonshops, this part is more often referred to as a coil and is intended for the movement of alcohol-containing vapors and the formation of condensate due to water cooling. An ideal coil is considered to be a glass spiral tube, where the entire process of separation of steam on the fraction will be visible. In fact, the copper tube is not inferior to glass with the only exception, which is opaque.

For high-quality bending of the copper tube under the serpent, it is pre-embanked by sand, after which the screwdriver is made. If the sand does not use, the thickness of the deflection will be uneven, and in some places the wall will come in touch, preventing the free passage of vapors.

All refrigerators with a serpentine are divided into 2 types:

The flow refrigerator is connected to the plumbing system and constantly passes through itself. Mandatory condition for the quality of the refrigerator is precisely cold water. If the moonshine is warm at the exit, it means that distillation is incorrectly, which will reduce the finished product.

Cold water is always fed from the bottom, and is always output from above, so that the countertop contributes to the timely cooling of the coil.

The bay refrigerator can only be used when there is no possibility to bring cold water. Not because too lazy, no time and desire, but because it is impossible. The principle of the fuel refrigerator is that a large amount of icy water is immediately poured, some even add ice. But the water still heats up over time, and the condensation of the steam is slower. On this frodder, the plums are made from above and forcefully pump off the water, feeding cold at the same time.

Connection of elements

After all the elements are prepared, they are connected to each other by silicone tubes. Often under the guise of silicone sell PVC tubes. They are not suitable for the compound, since the exit leave an unpleasant odor. How to check silicone or PVC? Very simple - set fire. Silicone burns badly and does not smell.

All connections should be sealed, for which you should think in advance and check them. Most often, the holes and locations of the connection are closed by a conventional dough from water and flour. If we are talking about a homemade moonshine based on a pressure cooker, this option is quite suitable. But if you plan to distill large volumes of mogon, then with the test there will be solid troubles - every time you clean it will be scraped and re-made it. And this is time and garbage.

Outdoor

The question of the presence of this element of the system causes a huge number of disputes. Some insist on the fact that the ancher is necessary because it additionally cleans the finished product from the sigh oil. Others, on the contrary, declare that there is no point in the additional design of such a trap, the second distillation will still need. What side of the barricades we will take, we are unknown, so we will tell about the manufacture of an ammunitor.

The main task of the amar furnace is to catch the rapidly cooler sevoyous oils and the exclusion of their ingress into the final product. It can be made from an ordinary glass jar with a capacity of 1 or 2 liters with a twisting hermetically lid. In the lid pre-make holes under the fittings. Screw them and connect with silicone hoses from one side with a distillation cube, on the other, with a refrigerator with a coil.

Some argue that if we put orange or lemon crusts into the surfactant, the moonshine with citrus scents. We tried, we did not work. Much more efficiently insist the moonshine on the same crusts for 3-7 days, and then the citrus fragrance will be clearly felt (it will not affect the taste).

Video How to make a moonshine device from the pressure cooker and the secrets of homemade production of moonshine

Making a moonshine using a pressure cooker

The pressure cooker is a saucepan, with valves for the withdrawal of steam and a hermetically closed lid. The main purpose of such a device is fast cooking. Despite this, quite often novice moonshoes apply it as a hermetic distillation cube to make alcoholic beverages. The pressure cooker is popular, because its cost is not big, and it is simple and quickly re-equipped. Consider more detailed how to make a moonshine apparatus properly from the pressure cooker.

Similarity of the pressure cooker and moonshine

The pressure cooker (Multicooker) in its structure resembles a traditional distiller. Its device is simple - this is a shopping pan with a tightly closing lid. According to its operational characteristics, it is quite similar to the usual cube. The use of the pressure cooker will save on the manufacture of kitchen utensils from food steel from scratch, because for this not only tools and material will be needed, but also experience. Consider how to make a moonshine with the help of a pressure cooker, which you can buy literally in any economic store.

Main composite parts

The design of the moonshine system in this situation is a distiller, which consists of a pressure cooker, which is used as a cube, connecting hoses and a refrigerator. In addition, to improve the quality of the moonshine into the system of distillation of the mogon at the request of a specialist such elements can be additionally mounted:

  • reflux;
  • several sumps;
  • filtering node;
  • Barboter.

Complex structures with pressure-windows type of the film film column are used very rare, as they have strict requirements for equipment characteristics, for example, volume, containers. In this situation, it will be better to make a distillation cube to order.

How to make a device for distillation of a moonshine with a pressure cooker?

For the organization of a reliable distiller, it is often used for the pressure cooker. This container has the following advantages:

    • High tightness with minimal refinement.
    • It is possible to apply outdated models of the pressing models, but provided that they do not have any malfunctions.
    • Due to the thick walls, a uniform warming up of the moonshine is ensured.
    • The risk of burning braga and its adhesion to the bottom is reduced.
    • Speed ​​has a non-stick coating.
    • Relatively low price.
    • The distillation system is compact and will not require a lot of space.
    • Easy application.

Make a moonshine apparatus based on the pressure cooker is quite simple. Even a novice moonshner, who is unfamiliar with the peculiarities of distillation technology will be able to make a moonshine system. Due to the pressure cooker, the temperature is kept steadily, without sharp drops and jumps. It is quite convenient for the preparation of moonshine at home.

Constructive features

Thanks to some constructive refinements that are associated to more with the processing of the pressure cooker, will allow standard economic utensils to turn into an ideal version of the evaporator, which will talk about below in the article.

Components

In order for the moonshine apparatus with your hands from the pressure cooker to turn into a good distillation design, such details will be necessary:

  • thermometer;
  • hermetic lid;
  • coil;
  • connecting hoses;
  • Tara collecting alcoholic beverage.

Refrigerator Greema

The distillation system is traditionally used with a refrigerator of a flow type. In the case when you cannot buy such an aggregate, then the serpent is done on your own. To do this, you will need pipes from metal. Initially, you should find a suitable "body" for the refrigerator, in which the coil is placed. Many for this use a portion of the pipe from polyethylene, which can be purchased in construction stores. They cut a piece of no more than 40-50 cm long cut off from it. Many specialists also use a conventional milk bidon to 5 liters.

In the lateral part of the case we make two small holes. The first should be located below the lid by 2-3 cm and at the same distance they do the second hole above the bottom. Next, fittings are mounted in the mounted lumen. Water is excreted from the upper hole, and the lowered liquid is already fed to the lower. Third hole should be done at the bottom of the wall - for the outlet of the coil, and the fourth slot in the lid - to combine the refrigerator with a steam pipeline.

The second version of the refrigerator is the fuel, which is used only if there is no possibility to bring cold water to the moonshine installation. The principle of operation of the fuel refrigerator is that a large amount of water is immediately poured into the container. Many specialists even additionally add ice. Liquid merges in two ways:

  • Forcibly rolls out with a special pump.
  • Merges through the upper slot.

Coil

This detail of the moonshine apparatus is made from the tube, the length of which is 200-270 cm. Push it off clean, sinking and dry sand. Do not forget to attach a plug in the form of a cavity. Such a tube is wound in the form of a spiral on a cylindrical basis. As such a base, a conventional pipe is used, but provided that its diameter should be 3-5 cm less than the inner cross section of the "body" of the refrigerator.

Important! All turns wink loosely. The distance between adjacent twists should be at least 150 mm. This will ensure maximum heat exchange.

After you wound a serpent, take out the cap and pour out all the sand. This spiral part is attached to the refrigerator housing and sealed.

Refinement of evaporator

To make the perfect evaporator, you just need to improve the pressure cooker slightly. To do this, you need to embed two fittings into its cover, which will allow excellent tightness of the literality of the whole design. The first hole is necessary for connecting the evaporator with the refrigerator. The second hole is inserted with a thermometer tube, which will allow you to constantly check the temperature of the Braga.

Note! Ideally, that all the elements and tubes of the moonshine apparatus are metallic, because it is noticed that their plastic and rubber analogs attach a unpleasant flavor.

Do you need an oven?

Many moonshoes are mounted in moonshine sumps. It is believed that this way alcohol will be much cleaner, which means it is better. Permanent discussions about its feasibility of use are not stopped for a long time, because the alcohol is in any case the stage of forced cleaning, for example, activated carbon or manganese. It seems like double work. However, there will be an opinion of the Moonshit Environment that such a "primary cleaning" as a result allows you to get the best drink.

Specialists are advised to make a surfactant, from a simple glass jar of one liter. In the lid drilled two holes and attach special tubes to it. One of them connects the sump with a pressure cooker, and the other with a condenser.

Assembly

How to make a moonshine machine from a pressure cooker so that the device works fine for years? The most important and responsible point in the assembly of the whole design is to check all compounds for tightness. In some cases, it is possible to carry out additional processing of places to connect all elements. In this situation, you can use the usual dough or even plasticine. After cooking a moonshine, they must be deleted.

Choice of pressure cooker for the manufacture of a distiller

As we said above, the saucepan is a full-fledged distillation cube for making a moonshine. Modern models today are produced from a double bottom of a stainless steel. It is much less likely to acquire aluminum pots, but they should be used in self-angular caution. Despite many disputes, today the question of the harmfulness of such a metal at high temperatures remains open.

True, the main flaw of the distiller, which is made from the usual pressure cooker, is a small volume. Many models contain only 5-7 liters of fluid. Thanks to this, it is possible to get at the output of no more than 1.5 liters of a good moonshine. However, this indicator for beginners is considered satisfactory. Much less often, on store shelves, you can find volumetric models - up to 17 liters. By purchasing the former pressure cooper, it is necessary to test the integrity and health of the safety valve in advance.

Fitting with his own hands

If the valve (fitting) is not in the device of the distilted apparatus, the preparation of the alcohol for a person will not be safe. To mount this part, a hole of a small diameter is formed in the lid, in which the tube with a predetermined thread is inserted. It is tightly clamped with nuts to the lid, both with internal and from the outside. Nuts are compacted by special gaskets. By the same principle, the fittings are inserted under the discovery of distillate, institution and / or output of water.

Steaming

To remove the alcohol vapor from the multi-cooker, you will need a connecting tube, the diameter of which does not exceed 10 mm. It should be hermetically put on a pre-inserted fitting. You can buy a steam pipe, which is made of silicone, stainless steel, copper and less often from plastic or brass.

Many moonshoes with many years of experience note that it is best to apply a metal steam pipeline. They explain their choice by the fact that silicone, albeit strong and safe material for food, but very uncomfortable in operation. With increasing temperature, it softened and does not hold a form. For its fixation, an additional bracket may be needed. It is best to buy a steam line from a metal M-shaped. Connect this item directly to the height of the nut.

Important! The moonshine device should be collected at home in such a way that the sump is not without a reliable support, that is, so that it does not hang in the air.

It is advisable to get it on a solid foundation that can be made of metal or even a tree. Many experts hang this item to the clamps that screw in the walls.

Large loads, both on silicone and plastic steam pipeline, lead to the fact that the details fail. Ideally, the connecting parts are better to choose from metal. Connection locations are compacted by gaskets.

Useful advice

Little to make a moonshine apparatus from the pressure cooker. It is important to think about his proper care. Therefore, you should purchase a special protective paste, with which the elements of stainless steel are treated. Such cleaning drugs can be bought in the department of household goods in any supermarket. It is also necessary to worry about the lubrication of silicone elements. To do this, you will also need to purchase a special lubricant that can be found on the counters of fishing stores.

To increase the service life of the device, you need to adhere to simple rules and recommendations. For example, after making a moonshine, it is important to wait for all the design details completely cooled. Next, you can disassemble the system, and it is necessary to start it from the refrigerator. Initially, turn off the connecting tubes and a coil that you need to rinse and dry. Next, it is necessary to wash the height and other details well. When all the details are dry, then they need to apply protective pastes.

How to make a moonshine machine from the pressure cooker: instruction + tips

The modern range of factory moonshine devices is quite wide. There are locked containers of different volumes, power and configuration. Nevertheless, many moonshoes prefer to use self-made designs for the production of alcohol.

One of the popular options is the moonshine from the pressure cooker.

Why kinderrilor

The pressure cooker is ideal as the basis for the future distillation apparatus.

First, it is made of high-quality food metal.

Secondly, there is a double / bimetallic bottom and hermetic cover in the tank.

Thirdly, the device is often equipped with a special valve to exit steam. These advantages simplify the process of manufacturing a distillation device and provide him with a long service life.

Capacity selection

First of all, you should decide on the parameters of the future apparatus. If the farm has an old pressure cooker, you can use it. Soviet versions are also suitable, and more modern, new and used, as well as failed. For a reasonable price, you can choose a good option on Chinese sites. If you want something more serious, you can search for dishes of European brands.

Before buying a capacity, pay attention to the following characteristics:

Volume. It is better to give preference to roomy options by 12-15 liters. Little classic pressure cookers on 5-7 liters are good for cooking, but for moonshine - no. At the exit you will get just a couple of alcohol liters.

Material. Optimally use of stainless steel products. From aluminum dishes it is better to refuse.

Availability of 1 or several valves for pressure relief. If they are not, you will have to drill the hole yourself.

Instructions for turning the pressure cooker to the moonshine apparatus

In the pressure cooker lid, we do the two holes using drill, insert the threads with a thread on ½ or ¾, press them to the cover with nuts on both sides, compounds with silicone or rubber gaskets.

If there is no pressure relief valve (as rarely), another hole will be required for it.

We screw the fittings to nipples: one - for a hose connecting the distillation cube with a refrigerator, the second - for a bimetallic thermometer.

Confirm thermometer, compounding with silicone or fum-ribbon.

Connect the silicone hose with a diameter of 1.2 cm, also taking care of tightness.

From the second side of the hose fix the refrigerator (serpentine). It can be purchased or improvised - from a copper or stainless tube.

A simple version of the moonshine from the pressure cooker is ready. It is quite suitable for the first experiences in moonshine. Optionally, it is possible to connect to the device, a drill, a barometer, a reflux and other devices.

Additional advice

If there is no gasket between the pan and the lid in the old pressure cooker, you can replace it with ready (buy in the store), cut out of a solid sheet or use special silicone for aquariums. The liquid material is poured over the groove at the edge of the lid and give it to dry for 1 day. Safe silicone is sold in construction stores.

Choosing the connecting elements and other details, it is better to give preference to copper and silicone.

Instead of nipple, you can embed a fitting into the cover with an outer thread, but in this case the pressure cooker will lose universality and will be used exclusively for moonshine.

The first test of the apparatus is better to spend, distilling water.

For emergency sealing, you can use the adhesive test.

Error or is there anything to add?

Methods for making a moonshine from a pressure cooker

Vinokura came up with a huge number of simple and improved devices. For distillation there are enough three main elements and one auxiliary. Collect a more perfect moonshine apparatus from the pressure cooker.

How to assemble the installation with your own hands?

The main element in the design is a pan that is applied without changes. In the pressure cooker it is necessary to remove the preliminary valve. Then the tube is fixed on the nozzle.

Collect the moonshine apparatus with their own hands from such elements:

Two hoses are put on the distiller - the water supply and removal of alcohol. In the pan poured BRAG 2/3 from the volume. The pressure cooker is tightly covered with a lid and put on fire.

Water in the distiller is supplied along the hose, which is connected to the crane. When the braga is heated to 70 degrees Celsius, it is necessary to reduce fire. The thermometer is installed if the pan has two safety valves. To do this, dismantle the second valve. It is installed in its place the thermometer sleeve.

The lid is upgraded as follows: Make two holes. The first is used to connect the container with the refrigerator, the other for the thermometer.

In this design, a laboratory distiller is used. The device can be made of copper tube. Skeins Mastery with a metal tool. If there is no such equipment, you can do the following.

In order not to spoil the copper pipe when flexing, sand falls asleep. Both sides are closed with traffic jams. Then you need to shake the pipe so that the sedimentary breed lay uniformly. After that, it can be bending - it is not deformed.

The moonshine apparatus from the pressure cooker is different:

When assembling an aggregate, it is important to check the tightness of the compounds.

For additional cleaning of the moonshine, the system will improve the drill. The device reduces distillation costs. The surfactant performs the following functions:

  • Braga is not mixed with the finished product;
  • The alcohol is cleaned without additional use of manganese or proteins;
  • Fragravizes moonshine.

Arykharnik does not affect the fortress.

How to make a moonshine apparatus from a pressure cooker so as not to connect to the water supply? To do this, you need to purchase a laboratory device - an air cooling distiller.

The design consists of such elements:

  • pressure cookers;
  • tubes (one thing);
  • laboratory distillator;
  • receiving capacity;
  • Heat source.

Laboratory distiller - a container with a diameter of 30 cm. Glass equipment has a steam fitting and alcohol outlet. The distillation flask is made of heat-resistant glass. A wide opening, side removal, a fixed plug - the advantages of the device.

The flask is calculated for 20 liters. Get such equipment is not easy. The system is designed for professional work.

Based on the pressure cooker, created modern equipment for the preparation of moonshine at home.

Apparatus "Neptune" based on pressure cooker

Moonshine equipment is equipped with pressure coins at 7, 9 and 11 liters. Installation price - 1600 rubles. If Neptune is completed with pots, the following amount is additionally added:

  • 2390 rubles costs 7-liter capacity;
  • 3100 rubles - 9-liter saucepan;
  • 3300 rubles - 11 liters.

The set of the distillator includes:

  • Clamp for fastening tubes - two pieces;
  • Silicone hose - 0.5 meters;
  • PVC tube for water - six meters;
  • nut 22 mm - two pieces;
  • adapter for the mixer;
  • Instruction.

During the preparation of equipment, the following performs:

  1. From the distiller columns, unscrew the nut and remove one gasket, and the second remains in place.
  2. The column is screwed into the hole, which is located in the pans lid. Important: The gasket must always be located on top.
  3. The second silicone element is installed from the inside and tighten the nut. It is necessary to check the density of the fit on both sides.
  4. Install the lid. Lower the lever and close it.

The lid of the moonshine apparatus has a concave form. One edge is lowered inside, slightly nadaviv. The thrust plate must rest in the edges of the pressure cooker. After that, the lever is lowered by one hand, and the other is sticking with a saucepan.

Hose put on a claw, tightening fasteners. One tube is installed on the upper fitting of the device, and the second mounted on the adapter for the mixer. If the tap with internal thread is screwed up adapter.

Wear a hose on the nozzle. Do not confuse a fitting for water supply. To do this, it is necessary to pour into the upper pipe, and the air will go out of the bottom. It is to it and connect the hose for the flow of water. All tubes are securely fixed by clamps.

The hose for finished alcohol is put on the free fitting. The manufacturer provided the equipment upgrades. The working area can be increased using several CARGs. With the help of such equipment, the degree of cleaning of alcohol increases. The higher the module, the better the alcohol gets.

Tsargi 20, 35, 50 cm perform the role of the column module. Additional parts (35 and 50 cm) allow you to get pure ethyl alcohol 96%. In each tsarge there are metal springs. The nozzle is represented in two materials - copper and stainless steel.

The kard is easily screwed into the Neptune instrument. At the same time it is necessary to check the presence of laying. Vinokura write that the assembly of the device is light and takes five minutes.

The instructions indicate that you first need to drive water for 10-15 minutes. The saucepan fill in Braga on 2/3 volumes. The productivity of the unit is 1.3 liters per hour.

  1. Small dimensions. The distiller is convenient to use at home.
  2. The unit is made of stainless steel.
  3. Laconic design.
  4. Ability to use on induction plates.
  5. Safety equipment.
  • no thermometer;
  • Latent marking from the outside.

In the basic apparatus "Neptune" eliminated flaws. Pan is designed for nine liters. A thermometer is built into the pressure cooker cap. This allows for one distillation cycle to get 85% alcohol.

The kit includes a container for braga by 33 liters. It is made of food plastic. The tank has a drain crane. The distiller is made of stainless steel brand AISI 304. The price of the base kit Neptune is 6800 p.

The set of optimal "Neptune" contains all the necessary equipment and accessories for moonshine. Installation price - 8500 p.

Distant devices made on the basis of the pressure cooker can be purchased in the store. Craftsman prefer to collect equipment on their own. The aggregates from the pressure cooker are suitable for cooking beverages at home in the kitchen.

Moonshine apparatus do it yourself

In private households of rural areas, especially on farms, there is always a decent amount of food vegetable waste. Firstly, they are quite sorry to simply throw out (given the fact that they can be used to prepare alcohol), and secondly, often branded alcohol sells very expensive from the place of deployment of the economy. One way or another, much more useful to have equipment for distillation. About how to make a moonshine apparatus with your own hands, let's tell further.

Composite parts of the design

Moonshine apparatus with your own hands to create at the same time and simple, and difficult. Just because it has a modular design, where each module can be created separately. And it is difficult due to the fact that the main thing here is to ensure the tightness of the entire contour. In addition, it is necessary to competently select materials for the manufacture of the device - not only the taste of the future moonshine depends, but also its health safety.

Moonshine apparatus with your own hands, drawings, schemes and pictures of which are of a different one, is mainly created from the standard set of blocks. Consider the process of creating each of the blocks separately.

At the same time, it is simple, and it is difficult to create a moonshine apparatus with your own hands.

Distillation

This is a container where the braga is poured for subsequent distillation. The distillation process itself is its boiling, as a result of which volatile alcohol pairs and fusion oils are distinguished (from which it is necessary to get rid of). That is, the distillation cube is essentially a capacious "saucepan", which should withstand both high temperature (at least 120 ° C) and pressure (up to 2 atmospheres).

In this case, the material of such a pan must be indifferent to the effects of valence alcohol-containing liquids.

A few words about the materials:

  1. The best definitely is the food stainless steel. Here can be used containers-tanks from the dining room (by 25 and 40 liters), but these containers are not so much common, and the stainless steel itself is a very expensive material. However, the cube, created precisely from the stainless steel, is almost eternal!
  2. In Soviet times, 30 liter dairy beedons made from aluminum were distributed in the countryside. Many moonshine devices were made exactly from them. However, aluminum at high temperatures react with essential oils and alcohol itself with the formation of saline harmful to health (hangover from such a moonshine will be extremely unpleasant), and in addition, the walls of such a bidon will be fattened. As a result, the service life of a cube of aluminum is not more than 5 years.
  3. Copper. It is an ideal material for the manufacture of a moonshine as a whole. First, it has sufficient heat capacity (for heating the cube or cooling distillate in the coil), and secondly, with copper reacts most of the fusion oils and ether (they form a characteristic film that is removed by citric acid). As a result, the moonshine in copper devices has the best quality and taste. In addition, copper is quite simple to solder, for it does not require high temperatures. Well, the main minus is the high cost of this material.
  4. Enameled containers. It may also be some kind of capacity from the catering company (volume, lithra 30, no less). Emale is absolutely indifferent to everything, and the fact that such a container is made of ordinary carbon steel, makes its cost quite acceptable.

In the distillation cube you need to load Braga, which means it should have a large on the dimensions of the lid. At the same time, it must keep high temperatures and pressure, that is, this cover should have locks and be high-qualityly compacted.

As a seal, use exclusively silicone gaskets. It is unacceptable to use rubber or PVC gaskets - when heated, they highlight not only bad components, but also dangerous to health substances that will condense along with alcohol!

Coil

This is a condenser. In shape, it is a spiral, wuting from a metal tube. Here, the evaporated alcohol is condensed. It is very important that this module is made from copper is a matter of moonshine quality.

However, it should be remembered that the serpentor created from the copper tube should be purified (citric acid) after each use.

You can produce a serpent with your own hands by taking the steel pipe (from 100 mm) and smoothly pushing the copper tube on it, a diameter of 12-15 mm. To make the copper tube, it should be filled with sand. If the thickness of the wall of the copper tube is 1 mm, then 2 meters will be enough for high-quality distillation.

Red and bubbler

This element is located between the cube and the coil. It is necessary for pre-purification of the moonshine from the sealed oils, the boiling point of which is more than 78 ° C. This element may have several technical embodiments at once:

Metal tube coil

This is a container, which can be used a conventional glass jar with inserted into the lid and hermetically sealed input and output tubes. Couples, getting into the jar, are strongly expanding, cooling, but evaporation of alcohol is quickly heated from the substance previously entered the alley and pass. As for the sealed oils, the temperature of their boiling is higher than 78 ° C, so they settled on the walls and the bottom of the jar.

Here is a hookah design. The tubes have a different length: one of them reaches almost to the bottom of the tank (banks), and the other is left short. The bottom of the container poured a fluid that can be aromaticized (for example, lemon zest). Couples from Cuba are passed through a long tube: under the influence of pressure created in Cuba, pairs pass through the liquid, some of them condense and mixed with it, and flavored alcohol pairs leave the bubbler through a short tube.

This is the same armor, only the water cooling of the container with pairs is added here. With the help of a larger point of temperature, it is possible to leave a larger number of impurities at the bottom of the bank, however, part of the precious alcohol is condensed. In order not to lose it, the liquid precipitate from the cans periodically pour back into the cube.

Moonshine

You can make a reflux for the moonshine apparatus with your own hands using 2 glass jars. At the same time, the external must have a very wide neck, so that an internal (small bank) passed into it. In the space between the walls of two cans should circulate water.

Refrigerator for moonshine

The snake can be cooled by ordinary air or even put it with ice. And it is possible - water. To do this, you should prepare this container - the refrigerator. Enough to take the usual bucket and immerse the serpentor there.

In this case, conventional cold water water can be used for cooling. It is only necessary to serve it with the help of the hose at the bottom of the bucket, so that it, gradually climbing up, heated, taking over the thermal energy of the condensing moonshine and merged into the drainage, poured over the edge of the bucket.

Connecting tubes

It is best to use copper tubes (due to the valuable properties of this metal for the uncerticulation process). In addition, copper is relatively easy to solder, ensuring the tightness of the entire contour. Any worthy alternatives (stainless steel tubes or glass) are technologically extremely complex in montage.

Parrot

The parrot for the distillation circuit is a device for automatic and continuous control of the fortress of the water-alcohol mixture at the outlet of the refrigerator of the moonshine. The theoretical base is based on elementary physics - the law of reporting vessels and archimedean power. The main part of the device is performed in the form of a cylinder filled with a moonshine, in which the area is floating (float).

Moonshine apparatus do it yourself

The moonshine under pressure enters the lower part of the cylinder and follows the "beak" - the flow at the top. It is best to use glass chemical flasks for this.

It is not worth (without at least) to make a "parrot" of plastic bottles. That polyethylene, which polypropylene enters with alcohol into a chemical reaction with the formation of polymer compounds harmful to the body. Poisoning will not come, but the hangover will be heavy.

How to make a moonshine apparatus with your own hands at home

The moonshine apparatus can be done at home. We will analyze the possible options.

The easiest option

A polyethylene bucket is used as a cube. Braga is poured into it. If the bucket has a capacity of 10 liters, then the brags should be poured no more than 4 liters. Further on threads (or ropes) over the surface of the Braga, a bowl is postponed, where the finished product will come. From above, the bucket is covered (downstream) with a polyethylene film, which, however, should have provisis in the center, but not touching the bowl.

Several boilers are used as a source of energy, which gently need to be placed inside the bucket before covering it with a film. Next, boilers are included, and the bucket is placed under the thin flowing of cold water. Braga boils, and the alcohol pairs begin to evaporate intensively, settle on the polyethylene screen, which is cooled with water and condensed.

The provisis of the screen ensures that the moonshine will begin to gather in the center and fall into a bowl.

The simplest moonshine apparatus

With 4 liters of 12-18-degree Braga, 1 liter of high-quality 45-degree moonshine can be obtained. However, after that it is mandatory to be cleaned or activated coal, or by manganese. Another option to improve the quality of the final product is to overtake the resulting moonshine again.

Such a "design" can be called the simplest moonshine double distillation created by your own hands.

From flask

With the help of two flasks and connecting their tubes, you can make a moonshine apparatus and apply it even in forest conditions. Braga is poured into one metal flask, and it is placed on fire (campfire, for example), and the other (hermetically connected to the first tube) is placed either into a water container or in the stream or in the lake.

The alcohol will be cooled and condensed in the second flask, however, there are certain subtleties here:

  • The capacity of the first flask should be significant to obtain a decent amount of moonshine in the second.
  • The tube must be made of metal (best of all copper).
  • In the second flask, it is necessary to provide a valve for blending excess pressure and displaced air. Of course, a part of alcohol vapors will go there, so high-quality cooling is very important here.

Here is such a simple instruction, how to make a moonshine apparatus with your own hands in forest conditions.

From pressure cooker

For moonshine purposes, you can use the pressure cooker. Such a device of the moonshine apparatus is presented with your own hands very practical, as there are no large tanks here, and you can gradually pour into it gradually (just as gradually picking up the finished product). The pressure cooker allows you to get a moonshine in small doses over a long period of time, without overwhelming any additional equipment.

Moonshine

Multivarka

Multicooker and pressure cooker use the same principle of cooking for a couple. Only in this case, instead of the water, we pour a braga.

From the medium

Actually, how to make a copper moonshine apparatus with your own hands, paid attention in the first section of the article. Just make sure that all the modules of the apparatus are made of copper.

Milk bidona

From aluminum dairy bidons, the moonshine, mainly chasing on the village. However, it needs further purification, because alcohol pairs at high temperature interact with aluminum.

With a column

Now the most popular moonshine devices equipped with distillation columns are very popular. They are round, conical parts mounted "Christmas tree" vertically and consistently. Couples consistently pass each of their such parts, and they settle various mogon fractions, which are then discharged with appropriate pipes.

The column, firstly, is needed to obtain alcohol of varying degrees of cleaning. Secondly, it is quite difficult to design it and collect it yourself. And thirdly, it is possible to clear the moonshine other, much less costly ways.

Moonshine of beer kegy

From beer kegy

This is a wonderful container for using it as a cube of the moonshine. However, to form a full-fledged device, you will need to collect all other modules. Many are used as a replacement to a surfactant distillation king. This gives effect (in terms of cleaning alcohol-containing vapors to their condensation), but it should be remembered that you should not collect the king for the moonshine apparatus - it's too thin and difficult.

From the pan

This is a completely working option if the volume of the pan begins, at least from 10 liters. The saucepan is a moonshine cube, and all other modular elements can be placed separately, even a kingua or distillation column. (However, it should be remembered that you are unlikely to collect a qualitative and efficient distillation column for the moonshine apparatus - you need factory accuracy here.

Automation for moonshine

When it comes to automating the refinement process, first of all, the automation of the cooling process is said. Often, people either are trying to save, or simply do not have access to running water and form autonomous cooling for the moonshine apparatus with their own hands: the serpent is simply immersed in a bucket with snow or water. Over time, the snow melts, water heats up and the condensation process is significantly worse. (In the tank of collecting the finished product, the non-condensed pairs under pressure begin to break through).

To avoid this, you must initially build a longer serpentine (for example, 4-5 meters). It can already be cooled with a fan or even by opening the window and creating a draft indoor (the method is called "in black"). Air is a very efficient cooler for the moonshine, which can be adapted with your own hands.

Homemade moonshine-based moonshops found recently tremendous popularity among consumers. The advantages of such an aggregate are undoubted. First, the pressure cooker can be bought in any store technique, secondly, it is an absolutely sealed container, equipped with two holes under the input and output valve. Thirdly, the built-in thermometer allows you to control the boiling point.

In order for the moonshine apparatus from the pressure cooker with their own hands it will only be necessary to increase the holes on the lid, add a refrigerator, an amar furnace and the simplest communications in the form of silicone hoses. How to do it right - in our article. Here you will find video from experienced dumbers and assembly recommendations.

The pressure cooker is a household appliance or pan with a hermetically closed lid. Due to such sealing during operation, increased pressure is formed, which allows you to prepare food at a higher temperature. This is how it is impossible to be suitable for the distillation of Braga. The pressure inside the pressure cooker reaches 200 kPa, which, on the one hand, allows Brage to boil faster, on the other - increase the speed of evaporation of alcohol-containing vapors.

What kind of pressure cooker will get a great moonshine apparatus

Choosing a pressure cooker, you need to pay attention to the wall thickness and the material from which they are made. Optimal is a pressure cooker from high-quality food stainless steel with a flat surface. This makes it possible to put an aggregate on any plane. Be sure to have 3-4 layers of the bottom, which will exclude the burning and loss of heat. Choose those devices that are used on a specific type of burner - gas, electrical or induction.

Moonshine apparatus from a pressure cooker with a surfactant

In addition, if you are just starting to learn moonshine, purchase a better electric pressure cooker equipped with a thermal sensor. This will allow you to establish a certain temperature and maintain it throughout the time of the distillation of Braga.

The disadvantage of such an apparatus is only one - small volume. The largest household pressure cooker consists of a 6-liter bowl. From this number of Braga, only 1-1.5 liters of the "dirty" moonshine will be obtained, and if you remove the tails and head and overtakes again, it turns out 0.75 liters. A little, of course, but quite enough for home use. Moreover, the cooking process itself is so simplified by the presence of a pressure cooker, which can be repeated on the same day.

In the pressure cooker, the braga is poured only on 2/3 volumes.

We collect a moonshine apparatus from the pressure cooker

In the pressure cooler cover, we saw the holes, in one of which the fitting or the feut is inserted, and in the second - bimetallic thermometer.

Sanitary futo provides the most sealed connection, so it will be better to stop on such threaded connections. For the lid you need 2 hours of 1/2 inches thread.

Fitting Fortorka for the moonshine from the pressure cooker   

A silicone hose for a connection with a coil is put on a feuttone, and in the second insert a bimetallic thermometer, if there is no built-in pressure cooker.

Thermometer

All connections must be absolutely hermetic so that the alcohol-containing pairs do not pass. Some prefer to make silicone plugs, others use the usual dough.

Connecting tubes that are connected by a distillation cube and a serpentine can be made of silicone - relatively inert material, withstanding high temperatures, as well as from glass - perfect option. You can stop the choice and on the copper tube, it also does not react with alcohol. It is strictly forbidden to use plastic and rubber hoses - the caustic smell and bitterness will be reduced to not all the cooking efforts.

This is how the scheme of the assembly of the moonshine apparatus from the pressure cooker is:

The scheme of the assembly of the moonshine from the pressure cooker

Condenser (Graham Refrigerator)

With regard to the moonshops, this part is more often referred to as a coil and is intended for the movement of alcohol-containing vapors and the formation of condensate due to water cooling. An ideal coil is considered to be a glass spiral tube, where the entire process of separation of steam on the fraction will be visible. In fact, the copper tube is not inferior to glass with the only exception, which is opaque.

For high-quality bending of the copper tube under the serpent, it is pre-embanked by sand, after which the screwdriver is made. If the sand does not use, the thickness of the deflection will be uneven, and in some places the wall will come in touch, preventing the free passage of vapors.

Copper coil

All refrigerators with a serpentine are divided into 2 types:

The flow refrigerator is connected to the plumbing system and constantly passes through itself. Mandatory condition for the quality of the refrigerator is precisely cold water. If the moonshine is warm at the exit, it means that distillation is incorrectly, which will reduce the finished product.

Cold water is always fed from the bottom, and is always output from above, so that the countertop contributes to the timely cooling of the coil.

The bay refrigerator can only be used when there is no possibility to bring cold water. Not because too lazy, no time and desire, but because it is impossible. The principle of the fuel refrigerator is that a large amount of icy water is immediately poured, some even add ice. But the water still heats up over time, and the condensation of the steam is slower. On this frodder, the plums are made from above and forcefully pump off the water, feeding cold at the same time.

Connection of elements

After all the elements are prepared, they are connected to each other by silicone tubes. Often under the guise of silicone sell PVC tubes. They are not suitable for the compound, since the exit leave an unpleasant odor. How to check silicone or PVC? Very simple - set fire. Silicone burns badly and does not smell.

All connections should be sealed, for which you should think in advance and check them. Most often, the holes and locations of the connection are closed by a conventional dough from water and flour. If we are talking about a homemade moonshine based on a pressure cooker, this option is quite suitable. But if you plan to distill large volumes of mogon, then with the test there will be solid troubles - every time you clean it will be scraped and re-made it. And this is time and garbage.

Outdoor

The question of the presence of this element of the system causes a huge number of disputes. Some insist on the fact that the ancher is necessary because it additionally cleans the finished product from the sigh oil. Others, on the contrary, declare that there is no point in the additional design of such a trap, the second distillation will still need. What side of the barricades we will take, we are unknown, so we will tell about the manufacture of an ammunitor.

Scheme of the moonshine with a surfactant

The main task of the amar furnace is to catch the rapidly cooler sevoyous oils and the exclusion of their ingress into the final product. It can be made from an ordinary glass jar with a capacity of 1 or 2 liters with a twisting hermetically lid. In the lid pre-make holes under the fittings. Screw them and connect with silicone hoses from one side with a distillation cube, on the other, with a refrigerator with a coil.

Outdoor

Some argue that if we put orange or lemon crusts into the surfactant, the moonshine with citrus scents. We tried, we did not work. Much more efficiently insist the moonshine on the same crusts for 3-7 days, and then the citrus fragrance will be clearly felt (it will not affect the taste).

Video How to make a moonshine device from the pressure cooker and the secrets of homemade production of moonshine

Homemade moonshine-based moonshops found recently tremendous popularity among consumers. The advantages of such an aggregate are undoubted. First, the pressure cooker can be bought in any store technique, secondly, it is an absolutely sealed container, equipped with two holes under the input and output valve. Thirdly, the built-in thermometer allows you to control the boiling point.

The pressure cooker is a household appliance or pan with a hermetically closed lid. Due to such sealing during operation, increased pressure is formed, which allows you to prepare food at a higher temperature. This is how it is impossible to be suitable for the distillation of Braga. The pressure inside the pressure cooker reaches 200 kPa, which, on the one hand, allows Brage to boil faster, on the other - increase the speed of evaporation of alcohol-containing vapors.

What kind of pressure cooker will get a great moonshine apparatus

Choosing a pressure cooker, you need to pay attention to the wall thickness and the material from which they are made. Optimal is a pressure cooker from high-quality food stainless steel with a flat surface. This makes it possible to put an aggregate on any plane. Be sure to have 3-4 layers of the bottom, which will exclude the burning and loss of heat. Choose those devices that are used on a specific type of burner - gas, electrical or induction.

In addition, if you are just starting to learn moonshine, purchase a better electric pressure cooker equipped with a thermal sensor. This will allow you to establish a certain temperature and maintain it throughout the time of the distillation of Braga.

The disadvantage of such an apparatus is only one - small volume. The largest household pressure cooker consists of a 6-liter bowl. From this number of Braga, only 1-1.5 liters of the "dirty" moonshine will be obtained, and if you remove the tails and head and overtakes again, it turns out 0.75 liters. A little, of course, but quite enough for home use. Moreover, the cooking process itself is so simplified by the presence of a pressure cooker, which can be repeated on the same day.

In the pressure cooker, the braga is poured only on 2/3 volumes.

Features of the pressure cooker

Why is the manufacture of a moonshine from the pressure cooker becomes popular? This can be explained by the simple structure of the main container. The pressure cooker is a saucepan or an appliance equipped with a hermetic lid. This design has a number of advantages. When the unit is running inside the pressure increases. This allows you to prepare dishes at a sufficiently high temperature. Thanks to this, food is preparing much faster than in a conventional saucepan.

This property allows you to use a pressure cooker to distillation of Braga. After all, the pressure inside such a design rises to 200 kPa. On the one hand, this makes it possible to prevent breags boiling, and on the other, to speed up the process of evaporation of alcohol-containing vapors.

What we need for the homemade apparatus

To work, you will need the following equipment and tools:

  1. Sprinkle for 6 or 9 liters.
  2. Nipples 20 mm.
  3. Fittings 20 mm.
  4. Gas hoses from stainless steel.
  5. Bank by 0.5 liters for the heightar.
  6. Change with refrigerator.
  7. Fiber drill 20 mm.
  8. Drill or screwdriver.
  9. Adjustable key.

In the store all nuts and fittings are made from brass, so you don't even try to search the stainless steel. This metal is not the worst option, so it will be quite enough for your device.

Is it difficult to do

How to make a moonshine apparatus from the pressure cooker? Is it difficult? Do such manipulations can be done at home and without someone else's help. The main thing is to know how the moonshine apparatus is arranged. To make it from the pressure cooker, it is necessary to increase the hole in the container, add an armhire and a refrigerator to it, as well as the simplest communications that allow you to merge the alcohol developed by the aggregate. In this case, it is recommended to use conventional silicone hoses.

Choose a pressure cooker correctly

How to start the process of manufacturing a moonshine from a pressure cooker? First of all, it is worth choosing a container. When buying a pressure cooker, special attention should be paid to the thickness of the walls, as well as the material from which such a saucepan is made. For the moonshine, use a strong stainless steel unit. In this case, the container should have a smooth surface. This will allow you to establish a design on any smooth table.

The number of layers at the bottom of the unit also matters. They should be from 3 to 4. Such a design will exclude the loss of heat and burning braga. It is also worth clarifying for what type of plate Site fit: induction, electrical or gas.

Electric pressure cooker

For those who want to make a moonshine apparatus from the pressure cooker with their own hands, but does not have the experience of moonshine, it is better to use electric technique. Such models of household appliances are usually equipped with a thermal sensor. This allows you to establish a certain temperature and maintain it throughout the distillation of the Braga.

Of course, such a pressure cooker has disadvantages. The most important is a small volume. It is necessary to take into account that for distillation of braga, the capacity should be filled only by 2/3. The volume of electrical pressure cooker is about 6 liters. At a time you can get no more than 1.5 liters of dirty alcohol. And if you overtake it again, then it turns out about 0.75 liters. This quantity is quite enough for home use. In addition, the process of obtaining alcohol is so simple that it can be repeated at any convenient time.

We collect a moonshine apparatus from the pressure cooker

In the pressure cooler cover, we saw the holes, in one of which the fitting or the feut is inserted, and in the second - bimetallic thermometer.

Sanitary futo provides the most sealed connection, so it will be better to stop on such threaded connections. For the lid you need 2 hours of 1/2 inches thread.

A silicone hose for a connection with a coil is put on a feuttone, and in the second insert a bimetallic thermometer, if there is no built-in pressure cooker.

All connections must be absolutely hermetic so that the alcohol-containing pairs do not pass. Some prefer to make silicone plugs, others use the usual dough.

Connecting tubes that are connected by a distillation cube and a serpentine can be made of silicone - relatively inert material, withstanding high temperatures, as well as from glass - perfect option. You can stop the choice and on the copper tube, it also does not react with alcohol. It is strictly forbidden to use plastic and rubber hoses - the caustic smell and bitterness will be reduced to not all the cooking efforts.

This is how the scheme of the assembly of the moonshine apparatus from the pressure cooker is:

Condenser (Graham Refrigerator)

With regard to the moonshops, this part is more often referred to as a coil and is intended for the movement of alcohol-containing vapors and the formation of condensate due to water cooling. An ideal coil is considered to be a glass spiral tube, where the entire process of separation of steam on the fraction will be visible. In fact, the copper tube is not inferior to glass with the only exception, which is opaque.

For high-quality bending of the copper tube under the serpent, it is pre-embanked by sand, after which the screwdriver is made. If the sand does not use, the thickness of the deflection will be uneven, and in some places the wall will come in touch, preventing the free passage of vapors.

All refrigerators with a serpentine are divided into 2 types:

The flow refrigerator is connected to the plumbing system and constantly passes through itself. Mandatory condition for the quality of the refrigerator is precisely cold water. If the moonshine is warm at the exit, it means that distillation is incorrectly, which will reduce the finished product.

Cold water is always fed from the bottom, and is always output from above, so that the countertop contributes to the timely cooling of the coil.

The bay refrigerator can only be used when there is no possibility to bring cold water. Not because too lazy, no time and desire, but because it is impossible. The principle of the fuel refrigerator is that a large amount of icy water is immediately poured, some even add ice. But the water still heats up over time, and the condensation of the steam is slower. On this frodder, the plums are made from above and forcefully pump off the water, feeding cold at the same time.

Connection of elements

After all the elements are prepared, they are connected to each other by silicone tubes. Often under the guise of silicone sell PVC tubes. They are not suitable for the compound, since the exit leave an unpleasant odor. How to check silicone or PVC? Very simple - set fire. Silicone burns badly and does not smell.

All connections should be sealed, for which you should think in advance and check them. Most often, the holes and locations of the connection are closed by a conventional dough from water and flour. If we are talking about a homemade moonshine based on a pressure cooker, this option is quite suitable. But if you plan to distill large volumes of mogon, then with the test there will be solid troubles - every time you clean it will be scraped and re-made it. And this is time and garbage.

Outdoor

The need for this element in the manufacture of a moonshine on the basis of a pressure cooker disputes are still underway. Experienced self-robes argue that such a device allows you to additionally clean the alcohol from the fusion oils. Others are stimpled that the surgery does not cope with such tasks, and the second distillation is required in any case. The choice is yours.

The main task of the amar furnace is to catch the rapidly cooler sevoyous oils and the exclusion of their ingress into the final product. It can be made from an ordinary glass jar with a capacity of 1 or 2 liters with a twisting hermetically lid. In the lid pre-make holes under the fittings. Screw them and connect with silicone hoses from one side with a distillation cube, on the other, with a refrigerator with a coil.

Among the professionals, it is believed that the crusts of lemon or orange placed in a surfactant can make it possible to give the final product to the taste and aroma of citrus fruits. But in most cases it is not possible to achieve such a result. The most effective method is to put in the container with the moonshine the same crusts from citrus fruits and wait a week. In this case, the taste of lemon or orange will be more clearly felt.

Disadvantages of pressure cooker for distillation

Because of the small volume, you will not be able to overtake more than 1 liter of the moonshine. However, if it is not critical for you, then you can open a saucepan right during distillation and pour a new braga there. With each time the quality of the moonshine will be worse, so it's not worth doing many times.

Aluminum in principle Bad fit for fermentation and distillation . Over time, it is oxidized and the taste of the metal is transferred to Braga, and in the end, both Moonshine. Therefore, it will be impossible to work for a long time with such a device, otherwise there will be a distillate together with something too bad and tasteless.

Other types of moonshine devices

A rather interesting option is a distiller based on a slow cooker, this kitchen household appliance simultaneously serves as a browse capacity and produces its uniform warming up, similar to the bean. Raw materials in it practically does not burn. In addition, in a slow cooker it is convenient to adjust the power, which simplifies-process distillation of the moonshine, makes it more convenient. As a result, even novice moonshoes can achieve high results without long workouts and rejected braga.

Another interesting option is the -Samogon apparatus from the flask -, most often it is intended for food products made of aluminum with food coating. This material has excellent thermal conductivity, which has a positive effect on the process of heating the braga, in addition it is fairly easy to process, which simplifies the refinement of the flasks. The main thing is that the protective coating of the capacity was integer, otherwise the metal will be released toxic oxides.

For the separation of elite alcoholic beverages by type -Vyski, brandy, Bourbon or brandy is perfect is a classic-diastiller from the medi. It is he who best retains the organoleptic properties of grain and -fructing brag-, transmitting that the most unique taste and aroma, known to each lover of high quality alcohol.

One of the vintage types of the distiller is a high-profile moonshine apparatus, which was used even when it could only dream about the direct-flow refrigerator .. However, such a configuration of a refrigerator, working without running water, can be quite relevant and in our days, when there is no access to Pipe water supply, such as in the country or in the village, or I want to save money for water in the counter.

One of the most exotic models is the moonshine double distillation apparatus, in which evaporation and condensation of the alcohol-containing fluid occurs more than once, and twice. This unit, invented almost forty years ago, but received distribution only in the last decade, is one of the most controversial models that divided the moonshoes on his jar of fans and irreconcilable opponents.

Soviet and modern pressure coils have excellent tightness, resulting in they can be used as a distillation cube . The main disadvantages are aluminum material and a small volume, which is why only 1 liter of a 40-degree moonshine will be made. Nevertheless, as an economist, you can use the ambulance version and today we will tell you how to make a moonshine device from it.

Our distiller will be equipped with a homemade driving one from the bank, so the product will be relatively clean. However, we are still recommended to perform a double distillation and be sure to separate the harmful factions. This is the guarantee of high-quality moonshine.

Distiller from the pressure cooker

The appearance of the finished distiller from the pressure cooker.

What do we need for a homemade apparatus?

To work, you will need the following equipment and tools:

Exterior of a distilted cube from a pressure cooker

The appearance of a distilted cube from a pressure cooker 9 liters.

  1. Sprinkle for 6 or 9 liters.
  2. Nipples 20 mm.
  3. Fittings 20 mm.
  4. Gas hoses from stainless steel.
  5. Bank by 0.5 liters for the heightar.
  6. Change with refrigerator.
  7. Fiber drill 20 mm.
  8. Drill or screwdriver.
  9. Adjustable key.

In the store all nuts and fittings are made from brass, so you don't even try to search the stainless steel. This metal is not the worst option, so it will be quite enough for your device.

I would like to immediately show the video from YouTube Channel SPAGYRIC1. which shows the appearance of the device from the pressure cooker, as well as the distillation process in real time. I note that the unit is equipped with an overwear, which we will also do soon.

Manufacturing of the moonshine from the pressure cooker

The process itself is best to look at the video, but I did not find decent videos, so we will study this process in the format of step-by-step instructions. We advise you to see the publication about the moonshine apparatus from the dairy flask, which is done by a similar principle.

I still lean to what is easier and cheaper to buy Ready serpentine with an amusement and a refrigerator which just attach to the pressure cooker and get the finished apparatus. It will be easier and most likely cheaper.

Sneakers with a surfactant

The coil with a drill stands in the area of ​​2.5 thousand rubles.

  1. We make a hole in the pressure cooker with a 20 mm drill.
  2. We insert nipple with thread, which can be lowered from the bottom with a silicone washer for tightness.
  3. Over the nipple, screw the fitting.
  4. The fitting can already be attached to any hose you choose.
  5. Then I recommend buying a ready-made snake in a specialized store (photo on the right), and just connect it with a hose.
  6. The device is ready, you can pour a braga or any alcohol-containing liquid.

In fact, all you have to do is drill a hole and spin several accessories. As a result, the device is ready for battle literally in 15 minutes.

The manufacture of the refrigerator is pretty difficult for its own. The only real budget version I saw George Caucasus In the video, which will be attached below.

There is a copper tube, which is inserted into the polypropylene tube and is embedded with a sealant from two sides. It turns out a full flow refrigerator.

Disadvantages of pressure cooker for distillation

Because of the small volume, you will not be able to overtake more than 1 liter of the moonshine. However, if it is not critical for you, then you can open a saucepan right during distillation and pour a new braga there. With each time the quality of the moonshine will be worse, so it's not worth doing many times.

Aluminum in principle Bad fit for fermentation and distillation . Over time, it is oxidized and the taste of the metal is transferred to Braga, and in the end, both Moonshine. Therefore, it will be impossible to work for a long time with such a device, otherwise there will be a distillate together with something too bad and tasteless.

Hello everyone! For a long time I promised to write this article, but he was constantly postponed. It's time to fulfill the promise. Today I will tell how to make a moonshine apparatus from the pressure cooker with your own hands.

What is the moonshine apparatus

Let's first remind you to start, from which it consists and how the homemade moonshine apparatus works. The simplest construction includes a distillation cube (boiling capacity) and a refrigerator (direct or serpentine). The diagram is shown in the figure below.

Moonshine technology

Braga is poured into hermetic container and heats up to evaporation of alcohol from it. The pair are then falling into the refrigerator, where they are condensed into the moonshine. Sometimes the design includes additional equipment, such as an amrernant. Read more in the article to prepare a moonshine.

We make a distillation cubic

I will make a distillation cube from the old Soviet aluminum pressure cooker for 6 liters. It is an almost perfect option for this.

I speak almost, because She has a significant drawback - its volume. You can pour into such a container not more than 5 liters of Braga, from which approximately 1 liter of 45% of the moonshine.

I do not lie to tell you, but it's enough to start driving a moonshine and understand whether you want to do this business. And the occupation is very exciting, believe me.

So, we have such a pressure cooker.

I got it from my parents, but also to buy it will not be difficult. I just found at Avito exactly the same as 400 rubles.

First of all, it is necessary to cut into the nipple cover to connect a distillation cube with a refrigerator. I will insert this, with a thread on ½ ".

In the lid there are already two holes for valves for pressure relief, we will not touch them. Let them perform their function. We will make a new hole with a drill on a tree with a size of 20.

Why on wood? Yes, it is just much cheaper than the metal drill, and the aluminum cuts very well.

First you need to mark the center and drill a small drill hole for centering.

And then drill it with a large drill.

If there are inaccurate edges, they must be cleaned with a small notch with a shallow notch. Now you can insert nipple.

After the drill size 20, the hole is well suited for nipple ½ ", I even had to apply the key to be screwed. He sat down so tightly that no additional gaskets or seals do not need.

From the inside, tighten the nipple nut.

It screws up the fitting for fastening the hose Ø12 mm.

If your pressure cooker has a gasket, the distillation cube for a homemade moonshine is ready. I did not have it. Therefore, we will make it.

We make a gasket for sealing cube

What a rubber got here is not suitable here, with contact with the moonshine couples, it will smell and spoil our entire product. It needs silicone here, and not simple, but food.

You can buy a ready-made gasket or if you do not find a suitable size, buy a sheet and cut the gasket yourself. They are sold in stores for moonshivers and in stores with laboratory equipment.

I will make a laying of liquid silicone for aquariums. It can be bought in pet stores, construction supermarkets and plumbing stores.

It is necessary for aquariums, it is precisely safe and does not give extraneous smells.

Fill with a small slide groove for laying on the lid and let Silicon dry. After a day, you can already start distillation.

Go to the next step.

We make a refrigerator

Now we need a refrigerator. You can buy it, for example here there is a good and inexpensive coil. And you can make it yourself. For this, I have a separate article - the manufacture of the direct-flow refrigerator.

Than to connect details

Now it remains only to connect the distillation cube and refrigerator. For this, I use a silicone hose with an inner diameter of 12 mm. The hose should also be made of food silicone. No rubber or PVC!

Now the moonshine apparatus is ready. In order to prepare your first drink this is enough.

Tips and comments

  1. You can add a self-made drill to this design.
  2. If the fitting in the lid is set with a gap, then it can be sealed with the same silicone.
  3. It would be possible to do without nipple, and into the cover to embed a fitting with an external thread at once. But with Nipples, we get a more versatile design.
  4. Moonshine must be driven correctly, for this I advise you to read the article - double fractional distillation.
  5. After the manufacture of the moonshine, I advise you to test it on distillation of water.
  6. For emergency seals, the leaks in the device fits well enough dough. I managed at all without a sealing gasket.

That's all. The process is very simple and not long. If you have ideas or comments, then leave them in the comments. I am always happy with constructive criticism. Also subscribe to the news, I will soon plan to add braga recipes.

So far. Dorofeev Paul.

Composite parts of the design

The scheme of the moonshine includes the required elements:

  • distillation cube (tank);
  • steam pipe;
  • an armhire;
  • Refrigerator (condenser).

Scheme of the moonshine

Central element - distillation cube

The heart of the moonshine is a distillation cube or a tank. Collecting homemade moonshine apparatus with your own hands, you need to start with it. It is a container in which Braga is poured and then heats up. Since intensive thermal reaction occurs in the reservoir, its reliability should not be doubted.

Distillation

The best option is a distillation cube from copper or steel. Aluminum capacitance will not fit - the metal will join the reaction with Braga and ruptures the taste of the final product, and such a tank will last long. Copper is considered the most preferable, but it is quite expensive, so the purchase of such a container will be the invoice. Usually, the moonshifts-shustaries use dishes and kitchen utensils - stainless steel pans or enameled, flasks from-under milk or beer kegs, pressure coats and even multicookers.

A homemade distillation cube from a conventional enamel pan will serve about 4 years. The container from the stainless steel is even more durable. For the apparatus collected by his own hands, you can choose the reservoir of the desired volume - from 5 to 100 liters. But according to the experienced moonshoes, the optimal option is a 25-35-liter container, with which an average of 1.5-3 liters of moonshine is obtained.

Connecting Elements System - Steam Ward

In the homemade moonshine, made by their own hands, uses the system of tubes for which alcohol pairs and fluid itself are transmitted. To their choice, too, you need to approach with the mind, because the quality of the auxiliary elements dependes the taste quality of the drink. It is better to buy stainless steel tubes - this metal remains neutral to the effects of heated alcohol vapors and alcohol itself and does not give harmful impurities.

Removal (steam pipe)

The steam pipe should be sealed, so for its assembly, additional elements are used - fittings and fittings, with which individual tubes of different diameters are connected to a single system. Full tightness can be achieved using insulating compositions, for example, the most common dough, which makes the locations of the connections.

Self-made drill

The quality of the handling distillate depends on how much impurities contains in it. To clean the beverage from them in the process of assembling a homemade moonshine apparatus, a healer is installed with their own hands. The easiest way to make it from the usual glass can be 0.75-1 l. It is closed with a lid, there are two holes in it and two hoses are fed to them, which fix and seal.

Refrigerator for moonshine

The most difficult part is a refrigerator or a condenser, whose task is to cool the alcohol pairs so that they turn into a liquid. You can buy this element already in the finished form, you can do yourself.

The refrigerator includes two components - a serpentine and a cooling source. A homemade coil for the moonshine apparatus can be made of glass or aluminum tube. The first option is preferable. But if you allow finance, it is best to buy a copper coil who is quickly cooled and does not affect the tasteful characteristics of the finished drink.

Refrigerator for moonshine do it yourself

Several requirements are presented to the snake tube:

  • The diameter of the section should be within 9-13 mm, if it is larger - the device will turn out too cumbersome;
  • The optimal length, according to experienced moonshoes, should be 1.6-2.2 m, if the strength of the resistance increases and the distillation process will increase;
  • The wall thickness should be 1-1.2 mm, with a smaller indicator, the cooling of the system will go more intensively, but it will be much faster to wear it easier.

How to make a refrigerator with your own hands:

  1. A flexible metal tube should be filled with sand, so that it has not accidentally crumby.
  2. We wear it on a cylinder with a diameter of about 30-35 mm, making the turns in 10-13 mm increments.
  3. We remove the sand, we rinse the tube inside the tube well.
  4. Insert a serpentine into the case - a piece of plastic pipe, install nozzles on it to sum up the flow water.
  5. Hermetically seal both ends of the design.

How to cook moonshine in multicooker equipment?

In order to prepare a moonshine in a slow cooker, you need to start to prepare a brawl. To do this, take sugar 2 kg and water 2 l, fresh yeast - 250 g, instead of sugar you can use berries, fruits, jam. Yeasts allow everything to be recycled in BRAG and at the same time produce carbon dioxide and alcohol. Braga will wander around 7-14 days, you need to put in heat. As soon as she acquires a sweet taste and stops driving a foam, you can proceed in the pasture.

Brand is perfect for barley malt. For the manufacture of such a six kg of finished barley malt, 25 liters of water and 300 g of fresh yeast. The malt is crushed, poured into a hot water container, stir so that the mass become homogeneous.

Further, the temperature must be lifted to 65 ° C and over time to lower up to 55-60 ° C; When porridge falls on the bottom, you need to remove the container from the plate and put in cold water. Dilute the yeast, add them to the wort, mix. Braga wanders around six days, with this every day it must be mixed.

The preparation procedure in the Multicooker is simple, but requires some sequence:

  • Pour the braga into the bowl.
  • Depending on the multicooker, find the "porridge soup" or "multipowner" modes, set the temperature of 120 ° C. After the foam was formed, slow down the temperature to 100 ° C.
  • The contact thermometer will need to maintain the breage temperature within + 65-68 ° C.
  • Next, you need to change the temperature of the slow cooker so that the braga is heated to +80 ° C. Gradually lift the breage temperature to +85 ° C. It is not necessary to raise the higher degrees, since the fusion oils are evaporated at such a temperature, which are harmful to health. Watch the moonshine strength not lower than 40 ° C.
  • Collect tails in a separate bank.

Some dumb triggers are used for an aggregate from a slow cooker. To do this, take the jar and drill two holes to which copper tubes are soldered. Flavors are placed in the surgract, which will give the final product a pleasant smell and taste. Arykharnik can be made of glass jar or copper. Copper capacity will be more reliable, and the glass of glass can be made faster.

Moonshine is ready. Now it needs to be cleaned and rid of harmful impurities and sharp smell. To do this, you can use manganese, activated carbon or products such as eggs, milk.

In order to give moonshine a pleasant smell, taste and color can be inscribed on herbs, nut membranes, berry juices, citrus sample. Thanks to such additives, the moonshine is pleasant and easier.

Making moonshine equipment in a slow cooker is easy. The process of moonshine is light, simple, fast and not costly. As a result, you will get a high-quality alcoholic drink.

A source

Apparatus "Neptune" based on pressure cooker

Moonshine equipment is equipped with pressure coins at 7, 9 and 11 liters. Installation price - 1600 rubles. If Neptune is completed with pots, the following amount is additionally added:

  • 2390 rubles costs 7-liter capacity;
  • 3100 rubles - 9-liter saucepan;
  • 3300 rubles - 11 liters.

The set of the distillator includes:

  • Clamp for fastening tubes - two pieces;
  • Silicone hose - 0.5 meters;
  • PVC tube for water - six meters;
  • nut 22 mm - two pieces;
  • adapter for the mixer;
  • Instruction.

During the preparation of equipment, the following performs:

From the distiller columns, unscrew the nut and remove one gasket, and the second remains in place. The column is screwed into the hole, which is located in the pans

Important: The gasket must always be located on top. The second silicone element is installed from the inside and tighten the nut. It is necessary to check the density of the fit on both sides. Install the cover

Lower the lever and close it.

The lid of the moonshine apparatus has a concave form. One edge is lowered inside, slightly nadaviv. The thrust plate must rest in the edges of the pressure cooker. After that, the lever is lowered by one hand, and the other is sticking with a saucepan.

Hose put on a claw, tightening fasteners. One tube is installed on the upper fitting of the device, and the second mounted on the adapter for the mixer. If the tap with internal thread is screwed up adapter.

Wear a hose on the nozzle. Do not confuse a fitting for water supply. To do this, it is necessary to pour into the upper pipe, and the air will go out of the bottom. It is to it and connect the hose for the flow of water. All tubes are securely fixed by clamps.

The hose for finished alcohol is put on the free fitting. The manufacturer provided the equipment upgrades. The working area can be increased using several CARGs. With the help of such equipment, the degree of cleaning of alcohol increases. The higher the module, the better the alcohol gets.

Tsargi 20, 35, 50 cm perform the role of the column module. Additional parts (35 and 50 cm) allow you to get pure ethyl alcohol 96%. In each tsarge there are metal springs. The nozzle is represented in two materials - copper and stainless steel.

The kard is easily screwed into the Neptune instrument. At the same time it is necessary to check the presence of laying. Vinokura write that the assembly of the device is light and takes five minutes.

The instructions indicate that you first need to drive water for 10-15 minutes. The saucepan fill in Braga on 2/3 volumes. The productivity of the unit is 1.3 liters per hour.

Advantages of the device:

  1. Small dimensions. The distiller is convenient to use at home.
  2. The unit is made of stainless steel.
  3. Laconic design.
  4. Ability to use on induction plates.
  5. Safety equipment.

Disadvantages of the aggregate:

  • no thermometer;
  • Latent marking from the outside.

In the basic apparatus "Neptune" eliminated flaws. Pan is designed for nine liters. A thermometer is built into the pressure cooker cap. This allows for one distillation cycle to get 85% alcohol.

The kit includes a container for braga by 33 liters. It is made of food plastic. The tank has a drain crane. The distiller is made of stainless steel brand AISI 304. The price of the base kit Neptune is 6800 p.

The set of optimal "Neptune" contains all the necessary equipment and accessories for moonshine. Installation price - 8500 p.

Distant devices made on the basis of the pressure cooker can be purchased in the store. Craftsman prefer to collect equipment on their own. The aggregates from the pressure cooker are suitable for cooking beverages at home in the kitchen.

Cooking Braga

For this, arm yourself by:

  • Two kilograms of sugar.
  • Two liters of water.
  • Fresh yeast - 250 g

The mass should be for about a week, it is necessary to keep it at a temperature not lower than 25 degrees. As soon as Braga becomes more pronounced and stopped forming a frothy mass, you can begin the reversal process.

MoonshineBryga from barley insist in a bank for about a week.

Excellent demonstrated themselves in the work of barley braga. For its manufacture, it is necessary to take up to six kilograms of the finished malt, 25 liters of pure water and 300 g of yeast mass. The malt is finely crushed, poured with hot water and is carefully stirred to achieve a homogeneous mass.

The temperature indicators are then needed to raise up to 60 degrees, and after a few hours it is again lowering for five degrees. When the cashem turns out to be on the day, the container is removed and placed in an ice vessel with water. Then the yeast is added to it, everything is thoroughly mixed. Braga must be up to the week, while it must be mixed daily.

After the creast taste appeared, and the foam will cease to form, you can begin to drive out an alcoholic drink. This procedure is quite simple.

Distillation

Every novice homemade alcohol lover chooses the mode to cook a quality drink, but if you have never been doing this, pay attention to such a program:

The device for the manufacture of alcoholic beverages can be made with their own hands from the primary items, and today you were convinced of this.

We collect a moonshine apparatus from the pressure cooker

In the pressure cooler cover, we saw the holes, in one of which the fitting or the feut is inserted, and in the second - bimetallic thermometer.

A silicone hose for a connection with a coil is put on a feuttone, and in the second insert a bimetallic thermometer, if there is no built-in pressure cooker.

Connecting tubes that are connected by a distillation cube and a serpentine can be made of silicone - relatively inert material, withstanding high temperatures, as well as from glass - perfect option. You can stop the choice and on the copper tube, it also does not react with alcohol. It is strictly forbidden to use plastic and rubber hoses - the caustic smell and bitterness will be reduced to not all the cooking efforts.

This is how the scheme of the assembly of the moonshine apparatus from the pressure cooker is:

Condenser (Graham Refrigerator)

With regard to the moonshops, this part is more often referred to as a coil and is intended for the movement of alcohol-containing vapors and the formation of condensate due to water cooling. An ideal coil is considered to be a glass spiral tube, where the entire process of separation of steam on the fraction will be visible. In fact, the copper tube is not inferior to glass with the only exception, which is opaque.

All refrigerators with a serpentine are divided into 2 types:

The flow refrigerator is connected to the plumbing system and constantly passes through itself. Mandatory condition for the quality of the refrigerator is precisely cold water. If the moonshine is warm at the exit, it means that distillation is incorrectly, which will reduce the finished product.

The bay refrigerator can only be used when there is no possibility to bring cold water. Not because too lazy, no time and desire, but because it is impossible. The principle of the fuel refrigerator is that a large amount of icy water is immediately poured, some even add ice. But the water still heats up over time, and the condensation of the steam is slower. On this frodder, the plums are made from above and forcefully pump off the water, feeding cold at the same time.

Connection of elements

After all the elements are prepared, they are connected to each other by silicone tubes. Often under the guise of silicone sell PVC tubes. They are not suitable for the compound, since the exit leave an unpleasant odor. How to check silicone or PVC? Very simple - set fire. Silicone burns badly and does not smell.

All connections should be sealed, for which you should think in advance and check them. Most often, the holes and locations of the connection are closed by a conventional dough from water and flour. If we are talking about a homemade moonshine based on a pressure cooker, this option is quite suitable. But if you plan to distill large volumes of mogon, then with the test there will be solid troubles - every time you clean it will be scraped and re-made it. And this is time and garbage.

Outdoor

The need for this element in the manufacture of a moonshine on the basis of a pressure cooker disputes are still underway. Experienced self-robes argue that such a device allows you to additionally clean the alcohol from the fusion oils. Others are stimpled that the surgery does not cope with such tasks, and the second distillation is required in any case. The choice is yours.

The main task of the amar furnace is to catch the rapidly cooler sevoyous oils and the exclusion of their ingress into the final product. It can be made from an ordinary glass jar with a capacity of 1 or 2 liters with a twisting hermetically lid. In the lid pre-make holes under the fittings. Screw them and connect with silicone hoses from one side with a distillation cube, on the other, with a refrigerator with a coil.

Among the professionals, it is believed that the crusts of lemon or orange placed in a surfactant can make it possible to give the final product to the taste and aroma of citrus fruits. But in most cases it is not possible to achieve such a result. The most effective method is to put in the container with the moonshine the same crusts from citrus fruits and wait a week. In this case, the taste of lemon or orange will be more clearly felt.

We make a distillation cubic

I will make a distillation cube from the old Soviet aluminum pressure cooker for 6 liters. It is an almost perfect option for this.

I speak almost, because She has a significant drawback - its volume. You can pour into such a container not more than 5 liters of Braga, from which approximately 1 liter of 45% of the moonshine.

I do not lie to tell you, but it's enough to start driving a moonshine and understand whether you want to do this business. And the occupation is very exciting, believe me.

So, we have such a pressure cooker.

I got it from my parents, but also to buy it will not be difficult. I just found at Avito exactly the same as 400 rubles.

First of all, it is necessary to cut into the nipple cover to connect a distillation cube with a refrigerator. I will insert this, with a thread on ½ ".

In the lid there are already two holes for valves for pressure relief, we will not touch them. Let them perform their function. We will make a new hole with a drill on a tree with a size of 20.

Why on wood? Yes, it is just much cheaper than the metal drill, and the aluminum cuts very well.

First you need to mark the center and drill a small drill hole for centering.

And then drill it with a large drill.

If there are inaccurate edges, they must be cleaned with a small notch with a shallow notch. Now you can insert nipple.

After the drill size 20, the hole is well suited for nipple ½ ", I even had to apply the key to be screwed. He sat down so tightly that no additional gaskets or seals do not need.

From the inside, tighten the nipple nut.

It screws up the fitting for fastening the hose Ø12 mm.

If your pressure cooker has a gasket, the distillation cube for a homemade moonshine is ready. I did not have it. Therefore, we will make it.

How to make a moonshine apparatus from the pressure cooker do it yourself at home

The unit of this kind consists of a small number of nodes, it is either the basic design of the distiller (cube, hoses and refrigerators), or a model containing the listed elements also one or more of the height and / or bubbots.

Distillation

First you need to choose a product by volume corresponding to the power of the alleged moonshine, or if the pressure cooker is already available, then customized under it the power of the refrigerator and the size of the hoses. With a standard volume of capacity in 5-7 liters, the moonshine output will be approximately 1-2 liters

If you need to make large volumes, it is worth paying attention to the pressurearves from such firms as "HASCEVHER", "ALPARI", "BOHMANN", "SHUNFA" or "TIANXI", in their assortment you can find models for 13-17 liters

The main security condition is the presence of an emergency discharge valve, although in new products it is almost guaranteed to be pre-installed, but in old, especially Soviet, it may not be. In the absence of such a mechanism, it can be installed independently by purchasing in a specialized store or on the Internet site. To seal the installation site, it is worth using a gasket made of food silicone or take advantage of a non-toxic heat-resistant sealant.

The same goes and the other two holes that will need to drill. The first is under the passing pairs, it is better to equip it with an outlet, which is convenient to mount the hose. The second is necessary for the thermometer. Under the bimetallic device it is better to establish an incoming threaded fitting, for an electronic - any sleeve with the corresponding diameter.

Selection of hose

When choosing steam pipelines from both metal and polymeric material, the main criterion is the indicator of the chemical inertness of the material. That is why it is impossible to use aluminum tubes that are easy to handle, but they allocate toxic oxides, it is similar to things with ordinary rubber, only it distinguishes non-oxides, but phenolic compounds. Food stainless steel excellent material, but very complex in processing, copper in this plan is better, but it is somewhat more expensive and requires careful wash after each distillation.

Refrigerator

The choice of two main designs: a serpentine or station. The first takes less space and with certain volumes of cooling casing can work without running water, but subject to the problem of condensate plugs. The second has a greater power, and in it condensate corks are not formed, but it works only from flowing water and takes a relatively a lot of space, which is not always permissible in the conditions of small kitchens of Soviet apartments.

To make a refrigerator with your own hands, you need to have a detailed idea of ​​its principle of operation and structural bases of each model. The alternative is to purchase a glass refrigerator for laboratory equipment, it meets all the necessary criteria, it is inexpensive and during the Internet is a very affordable product.

https://www.youtube.com/watch?v=jdyj9gpuepcvideo CAN't Be Loaded Because JavaScript is Disabled: Gonim Mogon. Budget version number 1 (https://www.youtube.com/watch?v=jdyj9gpUEPC)

To collect such a design will not be problems, you just need a distillation cube hoses to connect to the refrigerator, and if you use a typenist or bubbler, they are connected between these nodes. To make a glass height with their own hands, you need a minimum of materials and efforts.

Creating a moonshine from the Sokalovka

Any easiest moonshine apparatus consists of two blocks:

  • evaporative device in which the formation of vapors of alcohol derived from the braga;
  • The condenser in which the received pairs go into a liquid state.

There are a number of other details added to the distiller to improve its performance, but they are no longer absolutely necessary.

Composite parts of the moonshine made from the Sokovarka:

  1. Capacity for the Braga, which is represented by the most coil.
  2. Thermometer.

Main refinement in Sokalovka, which will be required? Installing two nozzles. One of them will be used to remove the steam into the coil, the thermometer will be placed in the second. In the capacitance of the hustle collector, it is necessary to tightly close the hole.

A thermometer is installed in the evaporator, to control the temperature. This will allow you to track the separation of high-quality alcohol from harmful impurities. The novice winemaker is necessarily useful, with time and the appearance of experience from this item can be refused. It is advisable to place the thermometer into the container in the metal tube, on the one hand it should be posted. This is necessary for the prevention of the degrees itself from damage and enter particles into the liquid.

  1. Crane? We are necessary to regulate water supply, when using a flow of cooling type.
  2. Tube for collecting fluid? Copper pipe, suitable diameter, which will connect the parts of the device and merge the finished liquid in the container.
  3. Cooling unit or refrigerator, to reduce the temperature of the vapor of alcohol. With this element, the greatest difficulties may arise, despite the seeming simplicity of the design. The best way ? Purchase a ready-made coil in specialized stores is best suited made of quartz glass. If you take on an independent manufacture of this part, the optimal material will be a copper tube. It is necessary to wind the spiral of the desired dimer and put in the container, inside which the cooled fluid will be. The main task in the manufacture of a coil is to ensure good cooling of alcohol vapors, otherwise the quality of the finished product will significantly decrease.
  4. Tube connecting the parts of the device.

For these elements, the same copper tubes that will not join the reaction with alcohol are best. Other materials are able to leave an unwanted taste and smell in the finished drink. It is definiciently impossible to use rubber gaskets or connections from the same considerations. One of the appropriate options can be a corrugated gas pipe made of non-ferrous metal.

  1. Capacity for collecting the finished drink? It can be an ordinary kettle or any other capacitance available at your hand.
Moonshine

Sprinkle - useful in the farm saucepan with a hermetic lid and safety valves. With its help, you can not only prepare delicious dishes, but also to drive a moonshine. We will look at the simple design of the distiller from the pressure cooker, which is used by many experienced and beginner dumbers.

The moonshit apparatus from the pressure cooker has three important advantages over other models:

  • This is a ready-made hermetic distillation cube that requires minimal refinement;
  • Stainless steel pressure coins are sold everywhere and cost inexpensively;
  • Suitable old capacities that are no longer used for cooking.

Lack only one is a small capacity. Very rarely there are more than 5-6 liters with a volume of 5-6 liters. It turns out a mini moonshine apparatus for distillation of small batches of Braga, or you will have to distill in several goals.

Instructions for the manufacture of the moonshine from the pressure cooker

Scheme of the moonshine from the pressure cooker

Description of elements:

1 - pressure cooker cover; 2 - thermometer; 3 - tube; 4 - crane; 5 - water cooling; 6 - self-receiver; 7 - stock; 8 - water sauna.

1. Refinement of the evaporator

It is only necessary to modify the cap of the pressure cooker slightly slightly, namely it is to cut two plumbing feuts with a thread ½ or ¾ inches. You can use fittings, but the feet are preferable because they provide better tightness. The first hole is required to connect the evaporator with the refrigerator through the tube, the thermometer is inserted into the second, which allows you to control the temperature of the braga.

All connecting tubes and other elements of the apparatus must be metallic (ideally copper), since their rubber and plastic analogs are left in the finished moonshine unpleasant flavor.

2. Condenser selection (refrigerator)

In most diagnostic schemes, the condenser is called a coil, in this module, the alcohol pairs turn into a liquid. An ideal option is considered a quartz glass cooler used in chemical laboratories. The second option is to make a coil from a copper tube, which you can buy on the construction market or in the plumbing store. For normal cooling of the homemade capacitor, we need running water.

For 1-2 hours of distillation, several hundred liters of water may be required. To reduce consumption, folk crafts apply a closed cooling system, a total of 30-40 liters. Two buckets are installed at different heights (drop 50-60 cm). From the top bucket, the water is chosen in a snake, from there runs to the bottom bucket. Next, aquarium pump or another pump is pumped back to the top bucket. But this scheme is only suitable for experienced dumbers, as it requires adjusting the flow rate of the fluid.

With the proper operation of the moonshine from the pressure cooker at the output of the sermogon, the moonshine should be cold, if it is distillate warm, it means that the device works incorrectly and refinement of the cooling system.

3. Connection of elements

At this stage, after the assembly, the sealing of all elements, especially connecting tubes is checked. Depending on the design, the joints have to be additionally processed. The easiest way to close all holes with a regular test, which is easily removed after distillation.

Moonshine

Design with a surfactant

About the need of an ammunition argue so far. Some believe that he removes part of third-party impurities. If you think so too, then you can make a moonshine apparatus from the pressure cooker with a surfactant. The design of the distiller will remain the same, just add another item. The diagram is depicted in the figure.

Moonshine apparatus with an ambernicker photo

As an alley, you can use a conventional glass jar with a twisted lid with a volume of 750 ml. In the lid, two holes are drilled in which tubes are soldered. One of them connects with a pressure cooker, the other - with a refrigeration unit.

Theoretically, with this scheme, a pair of ethyl alcohol and the fusion oils are first condensed in a surfactant. Then the alcohol re-boils, and the sigh oil remains at the bottom of the jar. But in practice there may be a variety of nuances associated with the temperature regime and the quality of the Braga.

P.S. The moonshine apparatus from the pressure cooker is excellent not only for obtaining a traditional sugar moonshine, Calvados, whiskey, brandy and other sturdy drinks can be expelled with it, which require distillation.

A few words about the pressure cooker

As you know, any moonshine apparatus is intended to get a strong alcoholic drink. This uses the distillation process or in a simple distillation. As for the pressure cooker, this is an ordinary pan with hermetically closed lid.

The cover of the lid is equipped with heat-resistant rubber, which allows it to fit tightly to the saucepan. In addition, there is a fastening, which is pressed with a plank with a spring and snap-down lock. Due to this, inside the tank increases the pressure, and the boiling point is rising (this is not better suitable for distillation of the braga), and special valves on the lid make the device safe.

The history of the pressure cooker begins not with cooking. For the first time, such a mechanism came up with French physicist and Pharmacist D. Papen back in the XVII century. It was he who found out that, working with such a device, some security should be observed:

  • The lid can only be opened by pre-pulling pairs;
  • Before opening the lid, it is better to cool the saucepan.

By the way, the housing of this container is made of high-quality iron, which withstands almost any load that occurs under the action of temperature and steam. After all, if at least one piece is broken, it is quite possible that an explosion will occur. In addition, it is impossible to open until the end of the process.

Choice of pressure cooker for the manufacture of a distiller

As we said above, the saucepan is a full-fledged distillation cube for making a moonshine. Modern models today are produced from a double-bottom stainless steel.

It is much less likely to acquire aluminum pots, but they should be used in self-angular caution. Despite many disputes, today the question of the harmfulness of such a metal at high temperatures remains open

True, the main flaw of the distiller, which is made from the usual pressure cooker, is a small volume. Many models contain only 5-7 liters of fluid. Thanks to this, it is possible to get at the output of no more than 1.5 liters of a good moonshine. However, this indicator for beginners is considered satisfactory. Much less often, on store shelves, you can find volumetric models - up to 17 liters. By purchasing the former pressure cooper, it is necessary to test the integrity and health of the safety valve in advance.

Fitting with his own hands

If the valve (fitting) is not in the device of the distilted apparatus, the preparation of the alcohol for a person will not be safe. To mount this part, a hole of a small diameter is formed in the lid, in which the tube with a predetermined thread is inserted. It is tightly clamped with nuts to the lid, both with internal and from the outside. Nuts are compacted by special gaskets. By the same principle, the fittings are inserted under the discovery of distillate, institution and / or output of water.

Steaming

To remove the alcohol vapor from the multi-cooker, you will need a connecting tube, the diameter of which does not exceed 10 mm. It should be hermetically put on a pre-inserted fitting. You can buy a steam pipe, which is made of silicone, stainless steel, copper and less often from plastic or brass.

Many moonshoes with many years of experience note that it is best to apply a metal steam pipeline. They explain their choice by the fact that silicone, albeit strong and safe material for food, but very uncomfortable in operation. With increasing temperature, it softened and does not hold a form. For its fixation, an additional bracket may be needed. It is best to buy a steam line from a metal M-shaped. Connect this item directly to the height of the nut.

It is advisable to get it on a solid foundation that can be made of metal or even a tree. Many experts hang this item to the clamps that screw in the walls.

Large loads, both on silicone and plastic steam pipeline, lead to the fact that the details fail. Ideally, the connecting parts are better to choose from metal. Connection locations are compacted by gaskets.

How to make a distiller with your own hands?

Start the process should be selected from the selection of the capacity of the pressure cooker.

You need to buy a stainless steel model having thick walls and a flat surface. The bottom of the product must have 3-4 layers.

This is not a difficult design for which you will need:

  1. Thermometer.
  2. Hermetically closing cover for tank.
  3. Coil.
  4. Silicone small diameter hoses.
  5. Vessel for the finished product.
  6. Crane.

The first step is to increase the hole in the cover of the device, which is inserted by the feutor or fitting, and the bimetallic thermometer.

For the product cover, the product is needed, whose size is ½ inches. It is put on this threaded element of a silicone hose that connects the unit with a coil.

If a bimetallic thermometer did not enter the pump kit, then it must be placed in the second hole. With it, you can track the fermentation temperature.

What to choose hoses for connecting? Glass tubes are considered the best for this, but they are difficult to buy. Therefore, alternative to them serve silicone. These hoses easily withstand high temperatures.

It is allowed to use copper pipes, they also do not react with alcohol.

Refrigerator Grahama

A homemade moonshine apparatus should be equipped with a coil.

The ideal refrigerator Graham is a quartz glass design, it has high strength. Through this material, it is possible to observe the process of separating the braga and the resulting substance on the part.

A homemade coil made from a copper plumbing tube is not inferior to glass. The only difference is that he is opaque.

Production:

  • For the manufacture of this part of the moonshine, the copper tube will need. It will be required to twist.
  • For this, the material must be filled with bulk substance (soda or sand).
  • Then you can proceed to the copper screw.
  • If this is not done, then the deflection will be uneven, which will continue to interfere with the passage of vapors. The coils of the coil are done loose.
  • For better heat exchange, the distance between the rings should be at least one and a half centimeters.

The video shows how to make a snake for the moonshine with your own hands:

Graham's refrigerator with a coil of two types:

The last type systematically skips cold water through itself. The device is connected to the water supply system, which requires a large water consumption. So that the unit performs all its functions at a high level, all conditions should be followed.

The bay type is more economical to use. However, in the production process, the liquid heats up, which makes the concentration of the steam weaker. Some craftsmen add ice to it, which is required for the normal operation of the device.

Outdoor

Companies are often conducted on the need for this part in the manufacture of the moonshine based on the pressure cooker. It serves to additionally clean the alcohol from the sigh oil.

Making a design can be made of glass liter cans:

  1. Capacity should be with a lid, which is sealed.
  2. It needs to make a small hole for fittings, screw them.
  3. After - to connect the resulting silicone hose with a refrigerator and a distillation apparatus.

Professionals claim to make a crust of lemon or orange in the surfactant, then this will give the citrus taste of the finished product. Having laid the same crust from citrus fruits for a week to the container, the taste of lemon or orange will be felt more saturated.

After the moonshine apparatus is fully assembled, the completion step will be checking it on hermeticity.

Special attention should be paid to the tubes that connect the design. Often they have to handle

  • For better tightness, the usual dough is used, as it is easily removed from the surfaces after the surveillance, but brings a lot of hassle, because The next time it needs to be done again.
  • Silicone plugs will also help when achieving this goal.

Why Sokovarka

It is assumed to use the classical metallic focus of Sovdepovsky times. Such a device consists of two saucepan? One for boiling water is located at the bottom, juice goes into the second, located above. From above there is a peculiar colander for vegetables and fruits covered with a lid. The process of manufacturing juice is simple? In the colander heats the raw material under the action of steam, which is formed in the lower tank with water. Juice drops are collected in the second container and, having passed sterilization, flow through a special tube into banks.

The main advantage of Sokolovka for moonshine is that its cover is closed almost hermetically. Such a moonshine apparatus will have all the necessary safety and protective valves. It requires the minimum amount of time and effort to get a high-quality evaporator. The only disadvantage of such an aggregate can be a small volume. But if the manufacture of homemade alcohol will occur only for personal purposes, it is not worth chaging for greater capacity.

Another advantage of the hiring in the process of moonshine is that it is capable of recycling large volumes of solid raw materials, such as apples or other fruits, to obtain brags.

The most elementary way? make a device from a hooker to obtain a moonshine without a serpentine. To do this, remove the cover, we install a pelvis or a saucepan, suitable in size. Fill it with cold water. In the bottom container we put BRAG. We put this design on the stove, the raw material is heated, the pairs rise up, touching the cold surface. They condense and flow down, fall into the container, which is originally designed to collect juice. The resulting liquid flows through the side taking hose into the container substituted under it.

Connecting the easiest coil with a refrigerator to the shortcock, you can get a high-quality moonshine apparatus.

Creating a moonshine from the Sokalovka

Any easiest moonshine apparatus consists of two blocks:

  • evaporative device in which the formation of vapors of alcohol derived from the braga;
  • The condenser in which the received pairs go into a liquid state.

There are a number of other details added to the distiller to improve its performance, but they are no longer absolutely necessary.

Composite parts of the moonshine made from the Sokovarka:

  1. Capacity for the Braga, which is represented by the most coil.
  2. Thermometer.

Main refinement in Sokalovka, which will be required? Installing two nozzles. One of them will be used to remove the steam into the coil, the thermometer will be placed in the second. In the capacitance of the hustle collector, it is necessary to tightly close the hole.

A thermometer is installed in the evaporator, to control the temperature. This will allow you to track the separation of high-quality alcohol from harmful impurities. The novice winemaker is necessarily useful, with time and the appearance of experience from this item can be refused. It is advisable to place the thermometer into the container in the metal tube, on the one hand it should be posted. This is necessary for the prevention of the degrees itself from damage and enter particles into the liquid.

  1. Crane? We are necessary to regulate water supply, when using a flow of cooling type.
  2. Tube for collecting fluid? Copper pipe, suitable diameter, which will connect the parts of the device and merge the finished liquid in the container.
  3. Cooling unit or refrigerator, to reduce the temperature of the vapor of alcohol. With this element, the greatest difficulties may arise, despite the seeming simplicity of the design. The best way ? Purchase a ready-made coil in specialized stores is best suited made of quartz glass. If you take on an independent manufacture of this part, the optimal material will be a copper tube. It is necessary to wind the spiral of the desired dimer and put in the container, inside which the cooled fluid will be. The main task in the manufacture of a coil is to ensure good cooling of alcohol vapors, otherwise the quality of the finished product will significantly decrease.
  4. Tube connecting the parts of the device.

For these elements, the same copper tubes that will not join the reaction with alcohol are best. Other materials are able to leave an unwanted taste and smell in the finished drink. It is definiciently impossible to use rubber gaskets or connections from the same considerations. One of the appropriate options can be a corrugated gas pipe made of non-ferrous metal.

  1. Capacity for collecting the finished drink? It can be an ordinary kettle or any other capacitance available at your hand.

Primitive distiller from bank

The casing of the moonshine is 3 liters of the bank with a conventional caproic lid. Is the main thing in such a device? Inner construction, consisting of a collection of mogon, watering can and condenser. The system is assembled with the help of ropes, fastens in a suspended condition to the cover through the holes pierced.

As a refrigerator, a metal jar is used (0.5 l) filled with by any fasteners of metal (bolts, nuts, nails) and water filled with water. The capacitor is frozen in the freezer before use. Watering can be made of a plastic floor-liter neck.

Pros and cons of the jar of moonshine in a slow cooker

But, before the construction of the structure, it is necessary to understand all the features of the device.

Benefits:

  • Thanks to existing programs in a slow cooker, it is easy to control the temperature indicators of the heating of the Braga. For this, you just need to specify a certain mode.
  • To remove unnecessary pairs, there are lid and valve.
  • You can control not only the heating temperature, but also the speed of the moonshine, which significantly simplifies the process for a person.

Due to this, the multicooker is an optimal household appliance that can be adapted to the sinking process. A professional device is obtained, which allows to obtain a high-quality alcoholic beverage based on malt or barley, and sometimes another basis. And using the height, you can enrich the taste of the outcome drink with additional flavors.

But, with all this, there are deficiencies in such a design:

  • Due to the use of rubber hoses, there is a chance that the harmful components from the material will fall into alcohol.
  • You need to be prepared for the fact that the amount of distilled alcohol at the output over a cycle will be quite small, but it will be.

We make a distillation cubic

I will make a distillation cube from the old Soviet aluminum pressure cooker for 6 liters. It is an almost perfect option for this.

I speak almost, because She has a significant drawback - its volume. You can pour into such a container not more than 5 liters of Braga, from which approximately 1 liter of 45% of the moonshine.

I do not lie to tell you, but it's enough to start driving a moonshine and understand whether you want to do this business. And the occupation is very exciting, believe me.

So, we have such a pressure cooker.

I got it from my parents, but also to buy it will not be difficult. I just found at Avito exactly the same as 400 rubles.

First of all, it is necessary to cut into the nipple cover to connect a distillation cube with a refrigerator. I will insert this, with a thread on ½ ".

In the lid there are already two holes for valves for pressure relief, we will not touch them. Let them perform their function. We will make a new hole with a drill on a tree with a size of 20.

Why on wood? Yes, it is just much cheaper than the metal drill, and the aluminum cuts very well.

First you need to mark the center and drill a small drill hole for centering.

And then drill it with a large drill.

If there are inaccurate edges, they must be cleaned with a small notch with a shallow notch. Now you can insert nipple.

After the drill size 20, the hole is well suited for nipple ½ ", I even had to apply the key to be screwed. He sat down so tightly that no additional gaskets or seals do not need.

From the inside, tighten the nipple nut.

It screws up the fitting for fastening the hose Ø12 mm.

If your pressure cooker has a gasket, the distillation cube for a homemade moonshine is ready. I did not have it. Therefore, we will make it.

Main composite parts

The design of the moonshine system in this situation is a distiller, which consists of a pressure cooker, which is used as a cube, connecting hoses and a refrigerator. In addition, to improve the quality of the moonshine into the system of distillation of the mogon at the request of a specialist such elements can be additionally mounted:

  • reflux;
  • several sumps;
  • filtering node;
  • Barboter.

Complex structures with pressure-windows type of the film film column are used very rare, as they have strict requirements for equipment characteristics, for example, volume, containers. In this situation, it will be better to make a distillation cube to order.

Capacity selection

First of all, you should decide on the parameters of the future apparatus. If the farm has an old pressure cooker, you can use it. Soviet versions are also suitable, and more modern, new and used, as well as failed. For a reasonable price, you can choose a good option on Chinese sites. If you want something more serious, you can search for dishes of European brands.

Before buying a capacity, pay attention to the following characteristics:

  1. Volume. It is better to give preference to roomy options by 12-15 liters. Little classic pressure cookers on 5-7 liters are good for cooking, but for moonshine - no. At the exit you will get just a couple of alcohol liters.

  2. Material. Optimally use of stainless steel products. From aluminum dishes it is better to refuse.

  3. Availability of 1 or several valves for pressure relief. If they are not, you will have to drill the hole yourself.

What kind of pressure cooker to choose?

You can, of course, to adapt to the distillation cube another Soviet pressure cooker on 5-6 liters. There were 2 modifications that differ in the type of shutter, but they were produced exclusively from aluminum. This material is ambiguous, its impact on the human body has little studied, but are known and described in the medical literature cases of poisoning by this metal.

It has been proven that it easily enters into chemical reactions with braga components. As a result, unpredictable compounds that may be improved, imperceptibly destroying health.

Caution. Recently, doctors have not recommended to cook food in aluminum dishes, especially if we are talking about acids and acids containing acid

Capacities are suitable for neutral products (dairy porridge, potatoes, etc.), but the finished product is also not recommended in them.

Yes, many moonshine devices and earlier, and are now made of aluminum dairy bids. What still does not prove the safety of this health material.

Therefore, it makes sense to think about acquiring a pressure cooker of stainless steel of modern production.

Still the most relevant and in demand remains capacity for 5-6 liters. Many suggestions and 9-liter tweezers. There will be 15 liters on the Internet (the issue price is about 3 thousand rubles).

But after all, the device you buy not only to obtain a distillate, but also to accelerate cooking. For example, meat in the pressure cooker is welded in 20 minutes, the keet - for 40, vegetables - for 5-7. Convenient and profitable.

We collect a moonshine apparatus from the pressure cooker

In the pressure cooler cover, we saw the holes, in one of which the fitting or the feut is inserted, and in the second - bimetallic thermometer.

A silicone hose for a connection with a coil is put on a feuttone, and in the second insert a bimetallic thermometer, if there is no built-in pressure cooker.

Connecting tubes that are connected by a distillation cube and a serpentine can be made of silicone - relatively inert material, withstanding high temperatures, as well as from glass - perfect option. You can stop the choice and on the copper tube, it also does not react with alcohol. It is strictly forbidden to use plastic and rubber hoses - the caustic smell and bitterness will be reduced to not all the cooking efforts.

This is how the scheme of the assembly of the moonshine apparatus from the pressure cooker is:

Condenser (Graham Refrigerator)

With regard to the moonshops, this part is more often referred to as a coil and is intended for the movement of alcohol-containing vapors and the formation of condensate due to water cooling. An ideal coil is considered to be a glass spiral tube, where the entire process of separation of steam on the fraction will be visible. In fact, the copper tube is not inferior to glass with the only exception, which is opaque.

All refrigerators with a serpentine are divided into 2 types:

The flow refrigerator is connected to the plumbing system and constantly passes through itself. Mandatory condition for the quality of the refrigerator is precisely cold water. If the moonshine is warm at the exit, it means that distillation is incorrectly, which will reduce the finished product.

The bay refrigerator can only be used when there is no possibility to bring cold water. Not because too lazy, no time and desire, but because it is impossible. The principle of the fuel refrigerator is that a large amount of icy water is immediately poured, some even add ice. But the water still heats up over time, and the condensation of the steam is slower. On this frodder, the plums are made from above and forcefully pump off the water, feeding cold at the same time.

Connection of elements

After all the elements are prepared, they are connected to each other by silicone tubes. Often under the guise of silicone sell PVC tubes. They are not suitable for the compound, since the exit leave an unpleasant odor. How to check silicone or PVC? Very simple - set fire. Silicone burns badly and does not smell.

All connections should be sealed, for which you should think in advance and check them. Most often, the holes and locations of the connection are closed by a conventional dough from water and flour. If we are talking about a homemade moonshine based on a pressure cooker, this option is quite suitable. But if you plan to distill large volumes of mogon, then with the test there will be solid troubles - every time you clean it will be scraped and re-made it. And this is time and garbage.

Outdoor

The need for this element in the manufacture of a moonshine on the basis of a pressure cooker disputes are still underway. Experienced self-robes argue that such a device allows you to additionally clean the alcohol from the fusion oils. Others are stimpled that the surgery does not cope with such tasks, and the second distillation is required in any case. The choice is yours.

The main task of the amar furnace is to catch the rapidly cooler sevoyous oils and the exclusion of their ingress into the final product. It can be made from an ordinary glass jar with a capacity of 1 or 2 liters with a twisting hermetically lid. In the lid pre-make holes under the fittings. Screw them and connect with silicone hoses from one side with a distillation cube, on the other, with a refrigerator with a coil.

Among the professionals, it is believed that the crusts of lemon or orange placed in a surfactant can make it possible to give the final product to the taste and aroma of citrus fruits. But in most cases it is not possible to achieve such a result. The most effective method is to put in the container with the moonshine the same crusts from citrus fruits and wait a week. In this case, the taste of lemon or orange will be more clearly felt.

Benefits of moonshine in a slow cooker

Among the advantages of the use of multicookers in moonshine:

  • The tightness of the design is already laid in the device, nothing needs to be seal, lubricate. One should only worry about that the tube is securely sitting in the novel of the valve.
  • The ability to change the temperature in the process of distillation is a very important feature that has each multicooker. Only in one models (simpler), these are pre-installed programs that have a "multipower" function, but also is carried out with the need for self-adjustment of the temperature regime.
  • Thanks to the non-stick coating of a multi-ware container, a distillation of grain or braga is possible with fruit particles.
  • Creating a high-quality moonshine using canopies, partially eliminating sigh oils (driving oil, bubblers).
  • The internal thermal sensor is available in the instrument supports the specified temperature with an acceptable accuracy. Therefore, the use of the thermometer is not necessarily, and it is quite difficult to place in the device.
  • Before the start of distillation, the multicooker can be opened, watching heating.

Of the disadvantages, perhaps, only a small capacity of a multicooker saucepan. For home use, the devices are most often acquired by 5-5.5 liters (with a real capacity to the maximum load mark of 4-4.5 liters).

This is enough for a family of 3-4 people. But there are 7 liters. Cost - from 3 thousand rubles. And for moonshit, it is not bad, and when cooking is not necessary to load completely.

Добавить комментарий